CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Petroleum Refinery Engineering
Comments
Question
Maximum viscosity of tar/PCM/fuel oil for easy and efficient atomisation in conventional burner is __________ centistokes (or 100 Redwood I seconds).
Options
A. 5
B. 25
C. 50
D. 100
Correct Answer
25
Petroleum Refinery Engineering problems
Search Results
1. Extractor temperature is maintained at -20°C in Edeleanu process to reduce the __________ of kerosene.
Options
A. smoke point
B. paraffins
C. aromatics
D. naphthenes
Show Answer
Scratch Pad
Discuss
Correct Answer: paraffins
2. Which of the following has the minimum °API gravity of all?
Options
A. Diesel
B. Kerosene
C. Petrol
D. Furnace oil
Show Answer
Scratch Pad
Discuss
Correct Answer: Furnace oil
3. Thermofer catalytic cracking process is a __________ process.
Options
A. fixed bed
B. moving bed
C. fluidised bed
D. non-catalytic
Show Answer
Scratch Pad
Discuss
Correct Answer: non-catalytic
4. The main reaction in reforming is the
Options
A. dehydrogenation of naphthenes.
B. hydrogenation of naphthenes.
C. hydrocracking of paraffins.
D. saturation of olefins.
Show Answer
Scratch Pad
Discuss
Correct Answer: dehydrogenation of naphthenes.
5. Which of the following reactions is undesirable in the production of catalytically reformed gasoline?
Options
A. Dehydrogenation of naphthene
B. Dehydrogenation of lower paraffins
C. Dehydrocyclisation of higher paraffins
D. Isomerisation of paraffins
Show Answer
Scratch Pad
Discuss
Correct Answer: Dehydrogenation of lower paraffins
6. Which of the following is a non-regenerative fixed bed catalytic reforming process?
Options
A. Hydroforming
B. Thermofer catalytic reforming
C. Platforming
D. Hyperforming
Show Answer
Scratch Pad
Discuss
Correct Answer: Platforming
7. A fuel oil consists of 4 fractions A, B, C and D. Their molar compositions and vapour pressures are given below :
The vapour pressure of the fuel oil will be __________ mm Hg.
Options
A. 736
B. 727.5
C. 512
D. 767.8
Show Answer
Scratch Pad
Discuss
Correct Answer: 736
8. Which of the following is not an important property of fuel oil/furnace oil?
Options
A. Sulphur content
B. Viscosity
C. Aniline point
D. Flash point
Show Answer
Scratch Pad
Discuss
Correct Answer: Aniline point
9. Cracking is
Options
A. an exothermic reaction.
B. an endothermic reaction.
C. favoured at very low temperature.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: an endothermic reaction.
10. Feed for reforming is generally
Options
A. naphtha or straight run gasoline.
B. reduced crude.
C. vacuum gas oil.
D. atmospheric gas oil.
Show Answer
Scratch Pad
Discuss
Correct Answer: naphtha or straight run gasoline.
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry