CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Petroleum Refinery Engineering
Comments
Question
The characterisation factor of a crude oil is calculated as 12.5. It means that; it is
Options
A. paraffinic
B. naphthenic
C. intermediate
D. none of these
Correct Answer
paraffinic
Petroleum Refinery Engineering problems
Search Results
1. The catalytic cracking of heavier petroleum fraction is done to produce mainly
Options
A. gasoline
B. asphalt
C. diesel oil
D. tar
Show Answer
Scratch Pad
Discuss
Correct Answer: diesel oil
2. Operating temperature and pressure in catalytic reforming is about
Options
A. 1-5 Kgf/cm
2
& 200°C.
B. 15-45 Kgf/cm
2
& 450-550°C.
C. 50 - 75 kgf/cm
2
& 600 - 800°C.
D. 5-10 kgf/cm
2
& 150 - 250°C.
Show Answer
Scratch Pad
Discuss
Correct Answer: 15-45 Kgf/cm
2
& 450-550°C.
3. Choose the correct statement.
Options
A. Octane number of i-octane is zero.
B. Octane number of paraffins increases with increasing number of carbon atoms.
C. Branched chain paraffins have higher octane number than straight chain paraffins with same number of carbon atoms.
D. The aromatics have lower octane number than naphthenes with same number of carbon atoms.
Show Answer
Scratch Pad
Discuss
Correct Answer: Branched chain paraffins have higher octane number than straight chain paraffins with same number of carbon atoms.
4. Petroleum is believed to have originated from __________ sources.
Options
A. vegetable
B. animal
C. both (a) and (b)
D. neither (a) nor (b)
Show Answer
Scratch Pad
Discuss
Correct Answer: both (a) and (b)
5. Which of the following hydrocarbons of same carbon atoms has minimum smoking tendency?
Options
A. Paraffins
B. Naphthenes
C. Aromatics
D. Iso-paraffins
Show Answer
Scratch Pad
Discuss
Correct Answer: Paraffins
6. In hydrofining catalytic desulphurisation process for sweetening of petroleum products, use of hydrogen
Options
A. enhances the desulphurisation process.
B. minimises coke formation.
C. both (a) and (b).
D. neither (a) nor (b).
Show Answer
Scratch Pad
Discuss
Correct Answer: both (a) and (b).
7. The doctor's solution comprises of sodium plumbite in
Options
A. alcohal
B. water
C. aqueous caustic soda
D. soda ash
Show Answer
Scratch Pad
Discuss
Correct Answer: aqueous caustic soda
8. Deoiling is the process of removal of oil from wax. It is done by the __________ process.
Options
A. solvent extraction
B. sweating
C. resettling
D. all (a), (b) & (c)
Show Answer
Scratch Pad
Discuss
Correct Answer: all (a), (b) & (c)
9. Hydrofining is the most recent and effective method for the
Options
A. removal of sulphur.
B. improvement of smoke point.
C. reduction of breathing loss.
D. improvement of viscosity index.
Show Answer
Scratch Pad
Discuss
Correct Answer: removal of sulphur.
10. The reservoir rock containing petroleum has
Options
A. low porosity
B. high permeability
C. high porosity
D. both (b) and (c)
Show Answer
Scratch Pad
Discuss
Correct Answer: both (b) and (c)
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry