CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Petroleum Refinery Engineering
Comments
Question
A petroleum well is called 'dry', if it contains
Options
A. very little oil.
B. no natural gas.
C. only natural gas.
D. all (a), (b) and (c).
Correct Answer
only natural gas.
Petroleum Refinery Engineering problems
Search Results
1. Mercaptans are added to liquefied petroleum gas (LPG) to
Options
A. reduce its cost.
B. narrow down its explosion limit.
C. assist in checking its leakage from cylinder.
D. increase its calorific value.
Show Answer
Scratch Pad
Discuss
Correct Answer: assist in checking its leakage from cylinder.
2. Penetration test determines the __________ of the grease.
Options
A. stiffness
B. lubricating properties (e.g. oilness)
C. service temperature
D. variation in viscosity with temperature
Show Answer
Scratch Pad
Discuss
Correct Answer: stiffness
3. Liquefied petroleum Gas (LPG) used for the household cooking comprises mainly of
Options
A. propane & butane
B. butane & ethane
C. methane & ethane
D. methane & carbon monoxide
Show Answer
Scratch Pad
Discuss
Correct Answer: propane & butane
4. Straight run petrol as compared to methyl/ethyl alcohol has
Options
A. lower calorific value.
B. lower octane number.
C. higher specific gravity.
D. higher ignition temperature.
Show Answer
Scratch Pad
Discuss
Correct Answer: lower octane number.
5. Aniline point is the
Options
A. characteristic property of diesel & lubricating oils.
B. measure of aromatic content of oil.
C. both (a) and (b).
D. neither (a) nor (b).
Show Answer
Scratch Pad
Discuss
Correct Answer: both (a) and (b).
6. Maximum use of petroleum coke is in
Options
A. adsorption refining operation.
B. fuel gas manufacture.
C. carbon electrode manufacture.
D. iron ore reduction.
Show Answer
Scratch Pad
Discuss
Correct Answer: carbon electrode manufacture.
7. Which of the following processes in oil refinery does not employ 'cracking'?
Options
A. Coking
B. Visbreaking
C. Pyrolysis
D. None of these
Show Answer
Scratch Pad
Discuss
Correct Answer: None of these
8. Absolute vapor pressure of petrofuels is found by Reid bomb which is heated in water bath to 100°F. In Reid apparatus, the ratio of the volume of air chamber to that of the liquid fuel chamber is
Options
A. 1
B. 2
C. 3
D. 4
Show Answer
Scratch Pad
Discuss
Correct Answer: 4
9. Pick out the wrong statement.
Options
A. Lower boiling paraffins have higher octane number than higher paraffins.
B. Dehydrogenation of naphthenes to aromatics is a desirable reaction in reforming process.
C. The most ideal feedstock for thermal reforming is dearomatised kerosene.
D. Catalyst used in catalytic reforming is platinum on silica-alumina base.
Show Answer
Scratch Pad
Discuss
Correct Answer: The most ideal feedstock for thermal reforming is dearomatised kerosene.
10. Pressure maintained in the high pressure primary tower of a three stage crude oil distillation system is about __________ kg/cm
2
.
Options
A. 1.5
B. 3
C. 6
D. 12
Show Answer
Scratch Pad
Discuss
Correct Answer: 3
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry