CuriousTab
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank Clerk
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Mechanical Operations
See What Others Are Saying!
Question
A __________ employs a set of screen across a flow channel for the separation of dirt/rust from a flowing liquid stream.
Options
A. thickener
B. classifier
C. strainer
D. clarifier
Correct Answer
strainer
More questions
1. Pick out the wrong statement about routing of fluids in a shell and tube heat exchanger.
Options
A. The corrosive and fouling fluid should be preferably routed through the tubes.
B. The viscous fluid should be routed through the shell side.
C. Lower flow rate fluid should be routed through the shell side.
D. Higher pressure fluid stream should be routed through the shell side.
Show Answer
Scratch Pad
Discuss
Correct Answer: Higher pressure fluid stream should be routed through the shell side.
2. Yield of coke oven gas in low temperature carbonisation of coal is about __________ Nm
3
/ton of dry coal.
Options
A. 60
B. 160
C. 500
D. 750
Show Answer
Scratch Pad
Discuss
Correct Answer: 160
3. Safety valves are provided in chemical equipments to guard against excessive
Options
A. temperature
B. pressure/pressure fluctuation
C. turbulence
D. noise
Show Answer
Scratch Pad
Discuss
Correct Answer: pressure/pressure fluctuation
4. For a reaction of the type,
, the rate of reaction (-
r
x
) is given by
Options
A. (
K
1
+
K
1
)
C
X
B. (
K
1
+
K
2
+
K
3
)
C
X
C.
K
1
C
V
-
K
2
C
X
D. (
K
1
-
K
2
)
C
X
Show Answer
Scratch Pad
Discuss
Correct Answer:
K
1
C
V
-
K
2
C
X
5. Silica bricks are attacked by basic slags at high temperature. Which of the following is not used solely as a binding material?
Options
A. aluminium phosphate
B. water
C. lime
D. plaster of paris
Show Answer
Scratch Pad
Discuss
Correct Answer: water
6. __________ have the same mass number, but different nuclear charge.
Options
A. Isotopes
B. Isobars
C. Isotones
D. none of these
Show Answer
Scratch Pad
Discuss
Correct Answer: Isobars
7. Fusion point of an acidic refractory material is
Options
A. increased by the addition of basic oxides.
B. reduced by the addition of basic oxides.
C. not affected by the addition of basic oxides.
D. always more than 2500°C.
Show Answer
Scratch Pad
Discuss
Correct Answer: reduced by the addition of basic oxides.
8. Introduction of slurry in a plate and frame filter press is done through a plate in each frame. The plate of this filter has a __________ surface.
Options
A. plane
B. curved
C. ribbed
D. either (a) or (b)
Show Answer
Scratch Pad
Discuss
Correct Answer: ribbed
9. With increase in the temperature of pure (distilled) water, its
Options
A. pOH decreases and pH increases.
B. pOH and pH both 4ecreases.
C. pH and pOH both increases.
D. pH decreases and pOH increases.
Show Answer
Scratch Pad
Discuss
Correct Answer: pOH and pH both 4ecreases.
10. Fresh sewage is __________ in nature.
Options
A. acidic
B. neutral
C. alkaline
D. highly acidic
Show Answer
Scratch Pad
Discuss
Correct Answer: alkaline
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry