Discussion
Home ‣ Chemical Engineering ‣ Process Equipment and Plant Design Comments
- Question
In packed towers provided with pall rings liquid redistributors are positioned at heights of every 6 metres or 5-10 times the column diameter, whichever is less. Maximum size of the pall rings should not exceed __________ of the column diameter.
Options- A. 1/10-1/15th
- B. 1/5-1/10th
- C. 1/20-1/30th
- D. 1/2 to 1/4th
- Correct Answer
- 1/10-1/15th
- 1. Diameter of bubble caps used in high pressure columns is __________ as compared to that used in identical vacuum columns.
Options- A. less
- B. more
- C. same
- D. either (a) or (b); no generalisation can be made Discuss
- 2. Normally, the plate thickness of the bottoms and roofs of vertically cylindrical storage vessels as compared to that of the cylindrical shell is
Options- A. more
- B. less
- C. same
- D. more or less depending upon the pressure & temperature inside the vessel and the nature of the fluid contained therein. Discuss
- 3. For a cylinderical vessel of moderate height, the weld joint efficiency for joints parallel to the cylinderical axis is given as 1.0, while for joints along the girth (circumference) it is given as 0.8. In calculating the shell wall thickness using code formula for an internally pressurised cylinderical vessel, what value of weld joint efficiency should be used?
Options- A. 0.8
- B. 0.9
- C. 1.0
- D. (0.8)0.5 Discuss
- 4. For pipe flows, head is proportional to __________ at constant capacity (where D = pipe diameter ).
Options- A. 1/D
- B. 1/D2
- C. 1/D5
- D. D2 Discuss
- 5. Width and depth of grooves in the tube sheet holes normally are __________ inch respectively.
Options- A.
- B.
- C.
- D.
Discuss
- 6. __________ of water makes it a widely used coolant in heat exchangers.
Options- A. Low corrosiveness
- B. Low dirt factor
- C. High specific heat
- D. Low viscosity Discuss
- 7. Pick out the wrong statement.
Options- A. Plate efficiency increases with increase in superficial vapour velocity till entrainment limit.
- B. Increase in depth of the liquid about the slots increases the plate efficiency, particularly if the liquid depth is < 1".
- C. Too small a plate spacing can cause a low efficiency, if the vapour velocity is greater than the allowable value.
- D. none of these. Discuss
- 8. Pick out the wrong statement pertaining to the design of a long tube vertical evaporator.
Options- A. Tube dia is 3-6 cms, while tube length in 3-6 metres.
- B. Steam is fed to the shell, whereas the liquor is filled inside the tube.
- C. Liquor level is maintained at l/3rd to 1/2 of the height of the tube.
- D. none of these. Discuss
- 9. In seive plate column, holes are drilled or punched in sizes ranging from 2.5 to 12 mm (5 mm being widely used). The hole pitch is normally __________ times the hole diameter to give the required hole area.
Options- A. 0.5 to 1.5
- B. 2.5 to 4.0
- C. 5 to 10
- D. 10 to 15 Discuss
- 10. Which of the following is the most common type of baffle used in industrial shell and tube heat exchanger?
Options- A. 75% cut segmental baffle.
- B. 25% cut segmental baffle.
- C. Orifice baffle.
- D. Disk and doughnut baffle. Discuss
Process Equipment and Plant Design problems
Search Results
Correct Answer: more
Correct Answer: less
Correct Answer: 0.8
Correct Answer: 1/D5
Correct Answer:
Correct Answer: High specific heat
Correct Answer: none of these.
Correct Answer: none of these.
Correct Answer: 2.5 to 4.0
Correct Answer: 25% cut segmental baffle.
Comments
There are no comments.More in Chemical Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.