Discussion
Home ‣ Chemical Engineering ‣ Process Equipment and Plant Design Comments
- Question
Skirt support is the most suitable for supporting __________ vessels.
Options- A. small horizontal
- B. large horizontal
- C. tall vertical
- D. thick walled
- Correct Answer
- tall vertical
- 1. In case of a shell and tube heat exchanger, the effect of L/D on inside film heat transfer co-efficient (hi) vanishes after a Reynold number of
Options- A. 1000
- B. 3000
- C. 5000
- D. 10000 Discuss
- 2. The practical representative values of HETP for a number of commercial operations lies within a range of __________ metre.
Options- A. 0.1-0.2
- B. 0.2-0.5
- C. 0.4-0.9
- D. 1.2-1.5 Discuss
- 3. Of the pressure vessels, with same thickness but different diameters, which one withstands higher pressure?
Options- A. Larger dia vessel.
- B. Smaller dia vessel.
- C. Larger dia long vessel.
- D. Strength of the vessel is same irrespective of the diameter. Discuss
- 4. Friction factor for turbulent flow in a new pipe is given by
Options- A.
- B.
- C. f = 0.22 NRe0.5
- D.
Discuss
- 5. For a cylinderical internally pressurised vessel, which of the following closure types would withstand highest pressure, if each closure is of the same material and thickness?
Options- A. hemispherical
- B. ellipsoidal (2 : 1)
- C. conical
- D. flat plate Discuss
- 6. Baffles may be eliminated for
Options- A. low viscosity liquids (< 200 poise).
- B. high viscosity liquids (> 600 poise).
- C. large diameter tanks.
- D. none of these. Discuss
- 7. In the case of a shell and tube heat exchanger, the logarithmic mean temperature difference
Options- A. is always less than arithmetic average value.
- B. is always more than arithmetic mean value and the geometric mean value.
- C. is always less than arithmetic mean value, but more than geometric mean value.
- D. may be either more or less than geometric mean and arithmetic mean value depending upon whether the flow of stream is co-current or counter-current. Discuss
- 8. Column support for the roof of cylindrical storage tank must be provided for
Options- A. small diameter tanks.
- B. large diameter tanks.
- C. small diameter tall tanks.
- D. all tanks irrespective of their heights and diameters. Discuss
- 9. Back-trapping in a distillation column results due to
Options- A. low gas velocity.
- B. high gas velocity.
- C. excessive liquid gradient over the tray.
- D. low reflux ratio. Discuss
- 10. Pick out the wrong statement about the design of seive plate column and the bubble cap column.
Options- A. The downcomer design and the residence time in the downcomer is almost same for seive plate and bubble cap columns.
- B. Weir length for a bubble cap plate is the same as that for the seive plate.
- C. Weir height for a bubble cap plate column is the same as that for a seive plate column.
- D. Weir height in case of a bubble cap plate ranges from 50 to 150 mm and is higher than the seive plate. Discuss
Process Equipment and Plant Design problems
Search Results
Correct Answer: 10000
Correct Answer: 0.4-0.9
Correct Answer: Smaller dia vessel.
Correct Answer:
Correct Answer: ellipsoidal (2 : 1)
Correct Answer: high viscosity liquids (> 600 poise).
Correct Answer: is always less than arithmetic average value.
Correct Answer: large diameter tanks.
Correct Answer: excessive liquid gradient over the tray.
Correct Answer: Weir height for a bubble cap plate column is the same as that for a seive plate column.
Comments
There are no comments.More in Chemical Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.