Discussion
Home ‣ Chemical Engineering ‣ Process Equipment and Plant Design Comments
- Question
Corrosion allowance in the design of pressure vessel/chemical equipment is not necessary, if
Options- A. plain carbon steel and cast iron parts are used.
- B. wall thickness is > 30 mm.
- C. material of construction is high alloy steel.
- D. both(b) & (c).
- Correct Answer
- both(b) & (c).
- 1. Smoker's equation for the calculation of number of equilibrium stages in a continuous binary distillation column is used, when the
Options- A. relative volatility is close to one (e.g., separation of close boiling isomers).
- B. feed is not at its bubble point.
- C. number of equilibrium stages in only stripping section is to be calculated.
- D. number of equilibrium stages required is likely to be very small. Discuss
- 2. For a given design of bubble cap, the number of bubble caps to be used per tray is set by the
Options- A. allowable gas velocity through the slots.
- B. plate spacing.
- C. diameter of the column.
- D. all (a), (b) and (c). Discuss
- 3. The type of stress developed in a metallic bar on subjecting it to a change in temperature without allowing it to be deformed is __________ stress.
Options- A. shear
- B. tensile
- C. compressive
- D. thermal Discuss
- 4. Normally, the ratio of the total riser area to the tower cross sectional area (for bubble cap towers of diameter more than 3 ft) is around
Options- A. 0.4-0.6
- B. 0.35-0.75
- C. 0.1-0.2
- D. 0.55-0.85 Discuss
- 5. Pick out the wrong statement pertaining to a shell and tube heat exchanger.
Options- A. The minimum value of baffle spacing is 50 mm.
- B. The maximum value of baffle spacing is equal to the I.D. of the shell.
- C. The maximum unsupported tube span is generally about 75 times tube diameter, but is reduced to about 60 times for aluminium, copper & alloys of these.
- D. Disk and doughnut baffle is the most commonly used baffle. Discuss
- 6. Oxygen carrying pipelines in chemical industries are coloured with __________ colour.
Options- A. yellow
- B. black
- C. blue
- D. red Discuss
- 7. Which of the following lengths of heat exchanger tubes are normally not used in practice?
Options- A. 2.5 metres
- B. 6 metres
- C. 10 metres
- D. 0.5 metre Discuss
- 8. Height of the flights in the rotary drier is in the range of
Options- A. 0.08 to 0.12 d
- B. 0.02 to 0.05 d
- C. 0.2 to 0.5 d
- D. 0.5 to 0.6 d Discuss
- 9. In packed absorption tower, onset of flooding usually occurs at a pressure drop of about __________ mm of water column per metre height of packing.
Options- A. 25-50
- B. 50-75
- C. 200-250
- D. 750-1000 Discuss
- 10. In a distillation column, minimum clearance to be maintained betweeen the overflow weir and the last row of the bubble caps is __________ cms.
Options- A. 2.5
- B. 7.5
- C. 15
- D. 20 Discuss
Process Equipment and Plant Design problems
Search Results
Correct Answer: relative volatility is close to one (e.g., separation of close boiling isomers).
Correct Answer: allowable gas velocity through the slots.
Correct Answer: thermal
Correct Answer: 0.1-0.2
Correct Answer: Disk and doughnut baffle is the most commonly used baffle.
Correct Answer: blue
Correct Answer: 10 metres
Correct Answer: 0.08 to 0.12 d
Correct Answer: 50-75
Correct Answer: 7.5
Comments
There are no comments.More in Chemical Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.