Discussion
Home ‣ Chemical Engineering ‣ Process Equipment and Plant Design Comments
- Question
In the allocated cap area, bubble caps are generally arranged on equilateral triangular pitch. Number of caps fixed on a plate is with a
Options- A. clearance of 25-75 mm.
- B. cap pitch of 1.3-2 times the cap diameter.
- C. either 'a' or 'b'.
- D. neither 'a' nor 'b'.
- Correct Answer
- either 'a' or 'b'.
- 1. To avoid the tearing off the plate of an edge, the margin (i.e., the minimum distance from the centre of the rivet hole to the nearest edge of the plate) should be equal to
Options- A. 0.5 d
- B. d
- C. 1.5 d
- D. 2.5 d Discuss
- 2. For turbulent flow (NRe > 2100) of low viscosity fluid (? > 20cp) in steel pipes, the optimum inside pipe diameter is given by(where, Q = fluid flow rate, ft3/sec.? = fluid density, lb/ft3 ? = fluid viscosity, centipoise Di = optimum inside pipe diameter, inches)
Options- A. Di, opt = 3.9 Q0.45 ?0.13
- B. Di, opt = 3.9 Q0.45 . ?0.95
- C. Di, opt = 4.7 Q0.36 . ?3.2?0.13
- D. Di, opt = 3 Q0.36 . ?0.88 Discuss
- 3. Typical static submergence for bubble cap plate column operating at atmospheric pressure may be around
Options- A. 2.5"
- B. 0.5"
- C. 5"
- D. 50% of the plate spacing Discuss
- 4. Value of Peclet number = 0, is the representative of
Options- A. laminar flow.
- B. complete back mixing.
- C. plug flow.
- D. eddy diffusivity = 0. Discuss
- 5. A/an __________ is used for changing the direction of a pipeline.
Options- A. elbow
- B. union
- C. flange
- D. disc compensator Discuss
- 6. Heat transfer co-efficient for a horizontal condenser as compared to a vertical condenser operating under similar conditions is
Options- A. same
- B. less
- C. about 3 times
- D. about 0.33 times Discuss
- 7. Hoop (circumferential) stress induced in a thin walled 'Horton Sphere' used for the storage of liquid ammonia under pressure is
Options- A.
- B.
- C.
- D.
Discuss
- 8. The wall thickness of thin cylindrical shell with hemispherical ends is __________ that of the spherical ends.
Options- A. equal to
- B. more than
- C. less than
- D. either (b) or (c); depends on maximum permissible internal pressure Discuss
- 9. Normally, the length to diameter ratio of rotary dryers varies form 4 to 10 and for its economic operation, the number of transfer units (NTU) for such dryers varies from
Options- A. 1.5-2.5
- B. 3.5-5.5
- C. 7.5-10.0
- D. 10-15 Discuss
- 10. Large process vessels operating under extreme temperature and pressure conditions are normally clad/ lined with materials like stainless steel, aluminium, nickel & its alloys, copper & its alloys and titanium. The cladding thickness is generally about __________ percent of the total thickness.
Options- A. 1 to 5
- B. 10 to 20
- C. 30 to 40
- D. 40 to 50 Discuss
Process Equipment and Plant Design problems
Search Results
Correct Answer: 1.5 d
Correct Answer: Di, opt = 3.9 Q0.45 ?0.13
Correct Answer: 0.5"
Correct Answer: complete back mixing.
Correct Answer: elbow
Correct Answer: about 3 times
Correct Answer:
Correct Answer: more than
Correct Answer: 1.5-2.5
Correct Answer: 10 to 20
Comments
There are no comments.More in Chemical Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.