CuriousTab
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank Clerk
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Process Equipment and Plant Design
See What Others Are Saying!
Question
In the design of a shell and tube heat exchanger, the corrosion allowance
Options
A. need not be provided for non-pressure parts like tie rods, spacers, baffles, supports etc.
B. for carbon steel and cast iron pressure parts is 1.5 mm (except for tubes) and for severe conditions it is 3 mm.
C. for internal cover and tube sheet is provided on both the sides.
D. all (a), (b) & (c).
Correct Answer
all (a), (b) & (c).
More questions
1. Thorium-232 (a fertile material) on absorption of a neutron gets converted into __________ , which is a fissile material.
Options
A. thorium-233
B. uranium-235
C. uranium-233
D. plutonium-239
Show Answer
Scratch Pad
Discuss
Correct Answer: uranium-233
2. Nucleus of tritium has __________ neutrons.
Options
A. 1
B. 2
C. 3
D. 5
Show Answer
Scratch Pad
Discuss
Correct Answer: 2
3. The phenomenon of radioactivity was discovered by
Options
A. Madam Curie
B. Bacquerrel
C. Roentgen
D. J.J. Thomson
Show Answer
Scratch Pad
Discuss
Correct Answer: Bacquerrel
4. Width and speed of a conveyor belt depends upon the __________ of the material.
Options
A. lump size
B. bulk density
C. both (a) & (b)
D. neither (a) nor (b)
Show Answer
Scratch Pad
Discuss
Correct Answer: both (a) & (b)
5. Bulk of the convective heat transfer resistance from a hot tube surface to the fluid flowing in it, is
Options
A. in the central core of the fluid.
B. uniformly distributed throughout the fluid.
C. mainly confined to a thin film of fluid near the surface.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: mainly confined to a thin film of fluid near the surface.
6. Bakelite is
Options
A. same as polytetra flouro ethylene (PTFE).
B. an inorganic polymer.
C. same as thermoset phenol formaldehyde.
D. not a polymer.
Show Answer
Scratch Pad
Discuss
Correct Answer: same as thermoset phenol formaldehyde.
7. Size reduction mechanism used in Jaw crushers is
Options
A. attrition
B. compression
C. cutting
D. impact
Show Answer
Scratch Pad
Discuss
Correct Answer: compression
8. Refractory bricks having lower porosity have
Options
A. high insulating properties
B. low heat capacity
C. low thermal conductivity
D. greater strength
Show Answer
Scratch Pad
Discuss
Correct Answer: greater strength
9. (CH
3
C
6
H
4
)
3
PO
4
is the chemical formula of
Options
A. triple superphosphate
B. tricresyl phosphate
C. flourapatite
D. superphosphate
Show Answer
Scratch Pad
Discuss
Correct Answer: tricresyl phosphate
10. Catalyst used in the oxidation of ammonia is
Options
A. platinum-beryllium
B. platinum-rhodium
C. cobalt-molybdenum
D. platinum-molybdenum
Show Answer
Scratch Pad
Discuss
Correct Answer: platinum-rhodium
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry