Discussion
Home ‣ Chemical Engineering ‣ Process Equipment and Plant Design Comments
- Question
In the design of a bag filter, the gas temperature is an important consideration, as it affects the
Options- A. gas density
- B. gas viscosity
- C. fibre selection
- D. all (a), (b) & (c)
- Correct Answer
- all (a), (b) & (c)
- 1. Shortest distance between two tubes is
Options- A. called tube pitch.
- B. called tube clearance.
- C. more in case of triangular pitch as compared to square pitch of tube layout.
- D. none of these. Discuss
- 2. The dust collection efficiency of electrostatic precipitator increases with increase in the
Options- A. gas flow rate.
- B. electrode area.
- C. both (a) & (b).
- D. neither (a) nor (b). Discuss
- 3. In a rotary drier, the average retention time of solid is(where Z = length of the drier, metres ? = apparent solid density, kg/m3 L = flow rate of dry solids, kg/see. m2 drier cross-section H = hold up of solid.)
Options- A.
- B.
- C.
- D.
Discuss
- 4. Value of Peclet number = ?, is the representative of
Options- A. laminar flow.
- B. complete back mixing,
- C. plug flow.
- D. eddy diffusivity = 0. Discuss
- 5. Hole diameter of the seive trays in the distillation column ranges from __________ mm.
Options- A. lto3
- B. 4 to 8
- C. 3 to 12.5
- D. 12.5 to 18.5 Discuss
- 6. Tube side heat transfer co-efficient for turbulent flow of liquid through tubes is proportional to
Options- A. G0.2
- B. G0.5
- C. G0.8
- D. G1.5 Discuss
- 7. Pick out the correct statement.
Options- A. It is preferred to use a vertical condenser for condensation of vapor from a distillation column without sub-cooling
- B. Draining of residual liquid on tray during shut down of distillation column is facilitated by weep holes.
- C. Random packing a packed tower offers the advantage of lower pressure drop and higher throughput of fluids as compared to regular/stacked packing.
- D. Risers are generally not connected to the plate in a distillation coloumn by bolts, rivets or welding. Discuss
- 8. __________ dished head is the strongest of all.
Options- A. Hemispherical
- B. Elliptical
- C. Torispherical
- D. none of these Discuss
- 9. In the design of a shell and tube heat exchanger, the corrosion allowance
Options- A. need not be provided for non-pressure parts like tie rods, spacers, baffles, supports etc.
- B. for carbon steel and cast iron pressure parts is 1.5 mm (except for tubes) and for severe conditions it is 3 mm.
- C. for internal cover and tube sheet is provided on both the sides.
- D. all (a), (b) & (c). Discuss
- 10. Flanges are connected to pipes by
Options- A. screwing
- B. welding
- C. brazing
- D. all (a), (b) and (c) Discuss
Process Equipment and Plant Design problems
Search Results
Correct Answer: called tube clearance.
Correct Answer: electrode area.
Correct Answer:
Correct Answer: plug flow.
Correct Answer: 3 to 12.5
Correct Answer: G0.8
Correct Answer: Risers are generally not connected to the plate in a distillation coloumn by bolts, rivets or welding.
Correct Answer: Hemispherical
Correct Answer: all (a), (b) & (c).
Correct Answer: all (a), (b) and (c)
Comments
There are no comments.More in Chemical Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.