Discussion
Home ‣ Chemical Engineering ‣ Process Equipment and Plant Design Comments
- Question
Hole diameter of the seive trays in the distillation column ranges from __________ mm.
Options- A. lto3
- B. 4 to 8
- C. 3 to 12.5
- D. 12.5 to 18.5
- Correct Answer
- 3 to 12.5
- 1. For a given fluid, as the pipe diameter increases, the pumping cost
Options- A. decreases.
- B. increases.
- C. remains unaffected.
- D. may increase or decreaes depending upon whether the fluid is Newtonian or non-Newtonion. Discuss
- 2. Ratio of tube length to shell diameter for a shell and tube heat exchanger is
Options- A. 8 : 1 to 12 : 1 for both liquid-liquid and gas-gas heat exchangers.
- B. 4 : 1 to 8 : 1 for liquid-liquid exchanger.
- C. < 4 : 1 for gas-gas exchangers.
- D. both(b) & (c). Discuss
- 3. Which of the following is the best tube material from thermal conductivity point of view alone?
Options- A. Aluminium
- B. Stainless steel
- C. Copper
- D. Carbon steel Discuss
- 4. In a shell and tube heat exchanger, triangular pitch arrangement as compared to square pitch arrangement
Options- A. results in higher shell side pressure drop.
- B. can accomodate less number of tubes for a given shell diameter.
- C. facilitates easier shell side cleaning; hence is more suitable for handling high dirt factor shell side fluid.
- D. creates relatively lower turbulence on the shell side resulting in lower shell side heat transfer co-efficient. Discuss
- 5. In a distillation column, bubble caps are located on trays with a pitch of __________ times the outside diameter of the caps.
Options- A. 1.3 to 2
- B. 1.6 to 2
- C. 2.5
- D. 1.5 to 3 Discuss
- 6. Value of Peclet number = ?, is the representative of
Options- A. laminar flow.
- B. complete back mixing,
- C. plug flow.
- D. eddy diffusivity = 0. Discuss
- 7. In a rotary drier, the average retention time of solid is(where Z = length of the drier, metres ? = apparent solid density, kg/m3 L = flow rate of dry solids, kg/see. m2 drier cross-section H = hold up of solid.)
Options- A.
- B.
- C.
- D.
Discuss
- 8. The dust collection efficiency of electrostatic precipitator increases with increase in the
Options- A. gas flow rate.
- B. electrode area.
- C. both (a) & (b).
- D. neither (a) nor (b). Discuss
- 9. Shortest distance between two tubes is
Options- A. called tube pitch.
- B. called tube clearance.
- C. more in case of triangular pitch as compared to square pitch of tube layout.
- D. none of these. Discuss
- 10. In the design of a bag filter, the gas temperature is an important consideration, as it affects the
Options- A. gas density
- B. gas viscosity
- C. fibre selection
- D. all (a), (b) & (c) Discuss
Process Equipment and Plant Design problems
Search Results
Correct Answer: decreases.
Correct Answer: both(b) & (c).
Correct Answer: Copper
Correct Answer: results in higher shell side pressure drop.
Correct Answer: 1.3 to 2
Correct Answer: plug flow.
Correct Answer:
Correct Answer: electrode area.
Correct Answer: called tube clearance.
Correct Answer: all (a), (b) & (c)
Comments
There are no comments.More in Chemical Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.