CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Stoichiometry
Comments
Question
Solutions having the same osmotic pressure are called __________ solutions.
Options
A. dilute
B. ideal
C. isotonic
D. saturated
Correct Answer
isotonic
Stoichiometry problems
Search Results
1. The forces causing the vaporisation of liquid are derived from the Kinetic energy of translation of its molecules. The heat of vaporisation
Options
A. increases with pressure rise.
B. decreases with increasing pressure.
C. becomes zero at the critical point.
D. both (b) & (c).
Show Answer
Scratch Pad
Discuss
Correct Answer: both (b) & (c).
2. For an ideal solution, the total vapor pressure varies __________ with the composition(expressed as mole fraction).
Options
A. inversely
B. exponentially
C. linearly
D. negligibly
Show Answer
Scratch Pad
Discuss
Correct Answer: linearly
3. Kinetic theory of gases stipulates that, the
Options
A. energy is lost during molecular collisions.
B. molecules possess appreciable volume.
C. absolute temperature is a measure of the kinetic energy of molecules.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: absolute temperature is a measure of the kinetic energy of molecules.
4. In physical adsorption, as compared to chemisorption, the
Options
A. quantity adsorbed per unit mass is higher.
B. rate of adsorption is controlled by the resistance to surface reaction.
C. activation energy is very high.
D. heat of adsorption is very large.
Show Answer
Scratch Pad
Discuss
Correct Answer: quantity adsorbed per unit mass is higher.
5. Validity of the relationship, inputs = outputs, holds good for the system at steady state
Options
A. with chemical reaction.
B. without chemical reaction.
C. without chemical reaction & losses.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: without chemical reaction & losses.
6. An equation for calculating vapour pressure is given by, log
10
P = A - B(t + c). This is called the
Options
A. Kistyakowsky equation
B. Antonic equation
C. Kopp's rule
D. Trouton's rule
Show Answer
Scratch Pad
Discuss
Correct Answer: Antonic equation
7. Heat of transition is the heat evolved or absorbed, when a substance is converted from
Options
A. vapor to liquid.
B. vapor to solid.
C. solid to liquid.
D. one allotropic form to another allotropic form.
Show Answer
Scratch Pad
Discuss
Correct Answer: one allotropic form to another allotropic form.
8. Weight of 56 litres of ammonia at N.T.P. is __________ gm.
Options
A. 2.5
B. 42.5
C. 56
D. 2800
Show Answer
Scratch Pad
Discuss
Correct Answer: 42.5
9. A solution with reasonably permanent pH is called a/an __________ solution.
Options
A. ideal
B. non-ideal
C. buffer
D. colloidal
Show Answer
Scratch Pad
Discuss
Correct Answer: buffer
10. Measurement of the amount of dry gas collected over water from volume of moist gas is based on the
Options
A. Charle's law.
B. Dalton's law of partial pressures.
C. Avogadro's hypothesis.
D. Boyle's law.
Show Answer
Scratch Pad
Discuss
Correct Answer: Dalton's law of partial pressures.
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry