CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Stoichiometry
Comments
Question
Total energy at a point comprises of __________ energy.
Options
A. potential & kinetic
B. pressure
C. internal
D. all (a), (b) & (c).
Correct Answer
all (a), (b) & (c).
Stoichiometry problems
Search Results
1. Number of gm moles of solute dissolved in one litre of a solution is called its
Options
A. equivalent weight
B. molarity
C. molality
D. normality
Show Answer
Scratch Pad
Discuss
Correct Answer: molarity
2. 1 centipoise is equivalent to
Options
A. 1 gm/cm.second
B. 1 centistoke
C. 2.42 lb/ft.hr
D. 2.42 lb/ft.second
Show Answer
Scratch Pad
Discuss
Correct Answer: 2.42 lb/ft.hr
3. The
pH
value of a solution is 5.9. If the hydrogen ion concentration is decreased hundred times, the solution will be
Options
A. basic
B. more acidic
C. neutral
D. of the same acidity
Show Answer
Scratch Pad
Discuss
Correct Answer: basic
4. 1 ata is equivalent to
Options
A. 1 atm.
B. 10 torr
C. 0.98 Pascal
D. 1 kgf/cm
2
Show Answer
Scratch Pad
Discuss
Correct Answer: 1 kgf/cm
2
5. Number of gm moles of solute dissolved in 1 kg of solvent is called its
Options
A. normality
B. molarity
C. molality
D. formality
Show Answer
Scratch Pad
Discuss
Correct Answer: molality
6. 1 BTU/ft
3
is approximately equal to __________ kcal/m
3
.
Options
A. 1
B. 9
C. 4
D. 252
Show Answer
Scratch Pad
Discuss
Correct Answer: 9
7. What is the total pressure exerted by a mixture of 0.45 kg mole of benzene, 0.44 kg mole of toluene and 0.23 kg mole of o-xylene at 100°C, if their vapor pressures at 100°C are 1340, 560 and 210 mmHg respectively?
Options
A. 756.2
B. 780.5
C. 801.5
D. 880.5
Show Answer
Scratch Pad
Discuss
Correct Answer: 801.5
8. Pick out the wrong statement:
Options
A. A vapor is termed as a saturated vapor, if its partial pressure equals its equilibrium vapor pressure.
B. A vapor whose partial pressure is less than its equilibrium vapor pressure, is termed as a 'superheated vapor'.
C. The temperature at which a vapor is saturated is termed as the boiling point.
D. The difference between the existing temperature of a vapor and its saturation temperature (i.e. dew point) is called its 'degree of superheat'.
Show Answer
Scratch Pad
Discuss
Correct Answer: The temperature at which a vapor is saturated is termed as the boiling point.
9. Hess's law of constant heat summation is based on conservation of mass. It deals with
Options
A. equilibrium constant.
B. reaction rate.
C. changes in heat of reaction.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: changes in heat of reaction.
10. A chemical process is said to occur under unsteady state, if the
Options
A. inventory changes do not take place.
B. ratio of streams entering/leaving are independent of time.
C. flow rates & composition both are time dependent.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: flow rates & composition both are time dependent.
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry