Discussion
Home ‣ Mechanical Engineering ‣ Automobile Engineering See What Others Are Saying!
- Question
The characteristic that is enhanced by the use of cylinder sleeves is
Options- A. cooling efficiency
- B. resistance to wear
- C. lubrication performance
- D. none of these
- Correct Answer
- resistance to wear
- 1. The order in which effort applied to the steering wheel is transferred to the front wheel is
Options- A. steering wheel - steering gearbox - steering shaft - tie rod - steering knuckle - front wheels
- B. steering wheel - steering shaft - steering gearbox - tie rod - steering kunckle -front wheels
- C. steering wheel - steering shaft - steering gearbox - steering knuckle - tie rod - front wheels
- D. steering wheel - tie rod - steering gearbox - steering shaft - steering knuckle - front wheels Discuss
- 2. Closed packed hexagonal space lattice is found in
Options- A. zinc, magnesium, cobalt, cadmium, antimony and bismuth
- B. gamma-iron, aluminium, copper, lead, silver and nickel
- C. alpha-iron, tungsten, chromium and molybdenum
- D. none of the above Discuss
- 3. The direct stress, across a principal plane, is known as principal stress.
Options- A. Yes
- B. No Discuss
- 4. The principal function of a stop valve is to
Options- A. control the flow of steam from the boiler to the main pipe and to shut off the steam completely when required
- B. empty the boiler when required and to discharge the mud, scale or sediments which are accumulated at the bottom of the boiler
- C. put off fire in the furnace of the boiler when the level of water in the boiler falls to an unsafe limit
- D. increase the temperature of saturated steam without raising its pressure Discuss
- 5. The alloying element which increases residual magnetism and coercive magnetic force in steel for magnets is
Options- A. chromium
- B. nickel
- C. vanadium
- D. cobalt Discuss
- 6. Stress concentration is caused due to
Options- A. variations in load acting on a member
- B. variations in properties of materials in a member
- C. abrupt change of cross-section
- D. all of these Discuss
- 7. In second type of levers,
Options- A. load is in between the fulcrum and effort
- B. effort is in between the fulcrum and load
- C. fulcrum is in between the load and effort
- D. none of these Discuss
- 8. In a lockgate, the reaction between two gates is (where P = Resultant pressure on the lock gate, and ? = Inclination of the gate with the normal to the side of the lock)
Options- A.
- B.
- C. P / 2sin?
- D.
Discuss
- 9. Slenderness ratio is the ratio of
Options- A. maximum size of column to minimum size of column
- B. width of column to depth of column
- C. effective length of column to least radius of gyration of the column
- D. effective length of column to width of column Discuss
- 10. The range of projectile on a downward inclined plane is __________ the range on upward inclined plane for the same velocity of projection and angle of projection.
Options- A. less than
- B. more than
- C. equal to Discuss
More questions
Correct Answer: steering wheel - steering shaft - steering gearbox - tie rod - steering kunckle -front wheels
Correct Answer: zinc, magnesium, cobalt, cadmium, antimony and bismuth
Correct Answer: Yes
Correct Answer: control the flow of steam from the boiler to the main pipe and to shut off the steam completely when required
Correct Answer: cobalt
Correct Answer: abrupt change of cross-section
Correct Answer: load is in between the fulcrum and effort
Correct Answer: P / 2sin?
Correct Answer: effective length of column to least radius of gyration of the column
Correct Answer: more than
Comments
There are no comments.More in Mechanical Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.