CuriousTab
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank Clerk
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Mechanical Engineering
‣
Engineering Materials
See What Others Are Saying!
Question
In the austempering process of heat treatment, austenite changes into
Options
A. martensite
B. troostite
C. sorbite
D. bainite
Correct Answer
bainite
More questions
1. For perfect intercooling in a two stage compressor,
Options
A.
B.
C.
p
1
=
p
3
D.
p
1
=
p
2
p
3
Show Answer
Scratch Pad
Discuss
Correct Answer:
2. In a beam of uniform strength, the bending stress developed is constant and is equal to the allowable stress at every section of the beam.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
3. The main task of a battery in automobiles is to
Options
A. supply electricity to the alternator
B. act as a reservoir or stabilizer of electricity
C. supply electricity to the vehicle's electrical system at all times while the engine is running
D. supply a large amount of power to turn the starter motor when the engine is being started
Show Answer
Scratch Pad
Discuss
Correct Answer: supply a large amount of power to turn the starter motor when the engine is being started
4. The motion of a particle round a fixed axis is
Options
A. translatory
B. rotary
C. circular
D. translatory as well as rotatry
Show Answer
Scratch Pad
Discuss
Correct Answer: circular
5. Cores are used to
Options
A. form internal cavities in the casting
B. improve mould surface
C. form a part of a green sand mould
D. all of these
Show Answer
Scratch Pad
Discuss
Correct Answer: all of these
6. The limestone in the charge of a blast furnace decomposes to give lime and carbon dioxide. The lime thus obtained
Options
A. controls the grade of pig iron
B. acts as an iron-bearing mineral
C. supplies heat to reduce ore and melt the iron
D. forms a slag by combining with impurities
Show Answer
Scratch Pad
Discuss
Correct Answer: forms a slag by combining with impurities
7. Which of the following statement is correct about EDM machining?
Options
A. It can machine hardest materials.
B. It produces high degree of surface finish.
C. The tool and work are never in contact with each other.
D. all of these
Show Answer
Scratch Pad
Discuss
Correct Answer: all of these
8. A good refrigerant should have
Options
A. high latent heat of vaporisation and low freezing point
B. high operating pressures and low freezing point
C. high specific volume and high latent heat of vaporisation
D. low C.O.P. and low freezing point
Show Answer
Scratch Pad
Discuss
Correct Answer: high latent heat of vaporisation and low freezing point
9. Which of the following statement is correct for oblique cutting system?
Options
A. The cutting edge is inclined at an angle less than 90° with the normal to the velocity of the tool.
B. Frequently, more than one cutting edges are in action.
C. The chip flows on the tool face at an angle less than 90° with the normal on the cutting edge.
D. all of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: all of the above
10. The maximum shear stress in a thin cylindrical shell subjected to internal pressure
p
is
Options
A.
pd
/
t
B.
pd
/2
t
C. pd
/4
t
D.
pd
/8
t
Show Answer
Scratch Pad
Discuss
Correct Answer:
pd
/8
t
Comments
There are no comments.
Enter a new Comment
Save
More in Mechanical Engineering:
Automobile Engineering
Compressors, Gas Dynamics and Gas Turbines
Engineering Materials
Engineering Mechanics
Heat Transfer, Refrigeration and Air Conditioning
Hydraulic Machines
Hydraulics and Fluid Mechanics
IC Engines and Nuclear Power Plants
Industrial Engineering and Production Management
Machine Design
Production Engineering
Steam Boilers and Engines
Steam Nozzles and Turbines
Strength of Materials
Theory of machines
Thermodynamics
Workshop Technology