CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Mechanical Engineering
‣
IC Engines and Nuclear Power Plants
Comments
Question
The fuel valve in a four stroke cycle diesel engine
Options
A. opens at 15° after top dead centre and closes at 20° before bottom dead centre
B. opens at 15° before top dead centre and closes at 20° after top dead centre
C. opens at top dead centre and closes at bottom dead centre
D. may open and close anywhere
Correct Answer
opens at 15° before top dead centre and closes at 20° after top dead centre
IC Engines and Nuclear Power Plants problems
Search Results
1. The __________ engines can work on very lean mixture of fuel.
Options
A. spark ignition
B. compression ignition
Show Answer
Scratch Pad
Discuss
Correct Answer: compression ignition
2. As compared to air standard cycle, in actual working, the effect of variation in specific heats is to
Options
A. increase maximum pressure and maximum temperature
B. reduce maximum pressure and maximum temperature
C. increase maximum pressure and decrease maximum temperature
D. decrease maximum pressure and increase maximum temperature
Show Answer
Scratch Pad
Discuss
Correct Answer: reduce maximum pressure and maximum temperature
3. In a four stroke engine, the working cycle is completed in
Options
A. one revolution of the crankshaft
B. two revolutions of the crankshaft
C. three revolutions of the crankshaft
D. four revolutions of the crankshaft
Show Answer
Scratch Pad
Discuss
Correct Answer: two revolutions of the crankshaft
4. An ignition coil in the spark ignition engines supplies __________ voltage to the spark plug.
Options
A. high
B. low
Show Answer
Scratch Pad
Discuss
Correct Answer: high
5. In a coil ignition system of petrol engines, a condenser is connected across the contact-breaker in order to
Options
A. prevent sparking across the gap between the points
B. cause more rapid break of the primary current, giving a higher voltage in the secondary circuit
C. both (a) and (b)
D. none of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: both (a) and (b)
6. Diesel as compared to petrol is
Options
A. highly ignitable
B. more difficult to ignite
C. less difficult to ignite
D. none of these
Show Answer
Scratch Pad
Discuss
Correct Answer: more difficult to ignite
7. Enriched uranium may contain fissionable contents from
Options
A. 1 to 40%
B. 10 to 50%
C. 1 to 80%
D. 1 to 99%
Show Answer
Scratch Pad
Discuss
Correct Answer: 1 to 99%
8. In petrol engines, using a fixed octane rating fuel, the increase in compression ratio will not effect the knocking tendency.
Options
A. Agree
B. Disagree
Show Answer
Scratch Pad
Discuss
Correct Answer: Disagree
9. The ignition quality of diesel oil is expressed by
Options
A. cetane number
B. octane number
C. calorific value
D. none of these
Show Answer
Scratch Pad
Discuss
Correct Answer: cetane number
10. If petrol is used in a diesel engine, then
Options
A. low power will be produced
B. efficiency will be low
C. higher knocking will occur
D. black smoke will be produced
Show Answer
Scratch Pad
Discuss
Correct Answer: higher knocking will occur
Comments
There are no comments.
Enter a new Comment
Save
More in Mechanical Engineering:
Automobile Engineering
Compressors, Gas Dynamics and Gas Turbines
Engineering Materials
Engineering Mechanics
Heat Transfer, Refrigeration and Air Conditioning
Hydraulic Machines
Hydraulics and Fluid Mechanics
IC Engines and Nuclear Power Plants
Industrial Engineering and Production Management
Machine Design
Production Engineering
Steam Boilers and Engines
Steam Nozzles and Turbines
Strength of Materials
Theory of machines
Thermodynamics
Workshop Technology