CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Mechanical Engineering
‣
IC Engines and Nuclear Power Plants
Comments
Question
The mechanical efficiency (?
m
) of the engine is given by
Options
A.
B.
C.
D. none of these
Correct Answer
IC Engines and Nuclear Power Plants problems
Search Results
1. The running cost of a petrol engine is __________ than that of a diesel engine.
Options
A. higher
B. lower
Show Answer
Scratch Pad
Discuss
Correct Answer: higher
2. Which of the following statement is wrong?
Options
A. In compression ignition engines, detonation occurs near the beginning of combustion.
B. Since the fuel, in compression ignition engines, is injected at the end of compression stroke, therefore, there will be no pre-ignition.
C. To eliminate knock in compression ignition engines, we want to achieve auto-ignition not early and desire a long delay period.
D. In compression ignition engines, because of hetrogeneous mixture, the rate of pressure rise is comparatively lower.
Show Answer
Scratch Pad
Discuss
Correct Answer: To eliminate knock in compression ignition engines, we want to achieve auto-ignition not early and desire a long delay period.
3. Supercharging __________ the power developed by the engine.
Options
A. has no effect on
B. increases
C. decreases
Show Answer
Scratch Pad
Discuss
Correct Answer: increases
4. In compression ignition engines, swirl denotes a
Options
A. haphazard motion of the gases in the chamber
B. rotary motion of the gases in the chamber
C. radial motion of the gases in the chamber
D. none of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: rotary motion of the gases in the chamber
5. The control rods in the control system of nuclear reactors are used to
Options
A. absorb excess neutrons
B. control fuel consumption
C. control temperature
D. all of these
Show Answer
Scratch Pad
Discuss
Correct Answer: absorb excess neutrons
6. A higher compression ratio causes
Options
A. pre-ignition
B. increase in detonation
C. an acceleration in the rate of combustion
D. any one of these
Show Answer
Scratch Pad
Discuss
Correct Answer: any one of these
7. The injector nozzle of a compression ignition engine is required to inject fuel at a sufficiently high pressure in order to
Options
A. inject fuel in a chamber of high pressure at the end of compression stroke
B. inject fuel at a high velocity to facilitate atomisation
C. ensure that penetration is not high
D. all of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: all of the above
8. In a two stroke engine, the working cycle is completed in two revolutions of the crankshaft.
Options
A. Correct
B. Incorrect
Show Answer
Scratch Pad
Discuss
Correct Answer: Incorrect
9. The mean effective pressure of a diesel engine having fixed compression ratio will __________ if cut off ratio decreases.
Options
A. increase
B. decrease
Show Answer
Scratch Pad
Discuss
Correct Answer: decrease
10. In a petrol engine, the mixture has the lowest pressure at the
Options
A. beginning of suction stroke
B. end of suction stroke
C. end of compression stroke
D. none of these
Show Answer
Scratch Pad
Discuss
Correct Answer: end of suction stroke
Comments
There are no comments.
Enter a new Comment
Save
More in Mechanical Engineering:
Automobile Engineering
Compressors, Gas Dynamics and Gas Turbines
Engineering Materials
Engineering Mechanics
Heat Transfer, Refrigeration and Air Conditioning
Hydraulic Machines
Hydraulics and Fluid Mechanics
IC Engines and Nuclear Power Plants
Industrial Engineering and Production Management
Machine Design
Production Engineering
Steam Boilers and Engines
Steam Nozzles and Turbines
Strength of Materials
Theory of machines
Thermodynamics
Workshop Technology