CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Furnace Technology
Comments
Question
To reduce the stack loss, heat recovery from flue gas can be done by
Options
A. preheating of cold stock.
B. preheating of combustion air.
C. steam generation in waste heat boilers.
D. all (a), (b) and (c).
Correct Answer
all (a), (b) and (c).
Furnace Technology problems
Search Results
1. Maximum heat transfer in high temperature furnaces is by
Options
A. conduction
B. convection
C. radiation
D. either (a), (b) or (c); depends on the type of furnace
Show Answer
Scratch Pad
Discuss
Correct Answer: radiation
2. The heat recoverable from flue gases of furnaces depends on the
Options
A. thermal efficiency of furnace.
B. quantity of flue gases.
C. flue gas temperature drop through the furnace.
D. all (a), (b) and (c).
Show Answer
Scratch Pad
Discuss
Correct Answer: all (a), (b) and (c).
3. Which of the following is not a directly fired furnace?
Options
A. By-product coke oven
B. Calcination kiln
C. Sintering furnace
D. Open hearth furnace
Show Answer
Scratch Pad
Discuss
Correct Answer: By-product coke oven
4. Power required in case of forced draught as compared to induced draught (for the same draught produced) is
Options
A. same
B. less
C. more
D. either more or less; depends on the flue gas density
Show Answer
Scratch Pad
Discuss
Correct Answer: less
5. Thermal efficiency of blast furnace stoves used for heating blast (air) may be about __________ percent.
Options
A. 20
B. 40
C. 60
D. 80
Show Answer
Scratch Pad
Discuss
Correct Answer: 80
6. Means for giving direction to the circulation of gases in furnaces are
Options
A. fans.
B. arrangement of heating stock in the furnaces.
C. location of outlet ports and heating & combustion devices.
D. all (a), (b) and (c).
Show Answer
Scratch Pad
Discuss
Correct Answer: all (a), (b) and (c).
7. Which furnace employs preheating, heating and soaking zones?
Options
A. Soaking pit
B. Reheating furnace
C. Open hearth furnace
D. Cupola
Show Answer
Scratch Pad
Discuss
Correct Answer: Reheating furnace
8. The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent.
Options
A. 15
B. 40
C. 70
D. 85
Show Answer
Scratch Pad
Discuss
Correct Answer: 40
9. Low stack loss indicates the
Options
A. use of sub-stoichiometric air for combustion.
B. efficient use of fuel.
C. inefficient use of fuel.
D. oxygen enrichment of combustion air.
Show Answer
Scratch Pad
Discuss
Correct Answer: efficient use of fuel.
10. Which is not a hearth furnace?
Options
A. Glass tank furnace
B. Open hearth furnace
C. Cupola
D. Reheating furnace
Show Answer
Scratch Pad
Discuss
Correct Answer: Cupola
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry