CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Fuels and Combustion
Comments
Question
The temperature at which plastic layer formation takes place during carbonisation of coal varies from __________ °C.
Options
A. 100 to 150
B. 350 to 450
C. 550 to 650
D. 700 to 850
Correct Answer
350 to 450
Fuels and Combustion problems
Search Results
1. Which of the following gaseous fuels has the lowest calorific value?
Options
A. Gobar gas
B. Refinery gas
C. Converter gas
D. Blast furnace gas
Show Answer
Scratch Pad
Discuss
Correct Answer: Blast furnace gas
2. Yield of coke oven gas in low temperature carbonisation of coal is about __________ Nm
3
/ton of dry coal.
Options
A. 60
B. 160
C. 500
D. 750
Show Answer
Scratch Pad
Discuss
Correct Answer: 160
3. In high temperature carbonisation of coal compared to low temperature carbonisation
Options
A. yield of ammonia is less.
B. aromatic content of tar is low.
C. H
2
content in the coke oven gas is more.
D. calorific value of the coke oven gas is lower.
Show Answer
Scratch Pad
Discuss
Correct Answer: H
2
content in the coke oven gas is more.
4. Pensky-Marten apparatus is used for those oils, whose flash points are __________ °F.
Options
A. <120
B. >120
C. <90
D. 90-110
Show Answer
Scratch Pad
Discuss
Correct Answer: >120
5. Adiabatic flame temperature of a fuel is dependent on the initial temperature of
Options
A. fuel
B. air
C. both (a) & (b)
D. neither (a) nor (b)
Show Answer
Scratch Pad
Discuss
Correct Answer: both (a) & (b)
6. Gross and net calorific value of a fuel will be the same
Options
A. if its ash content is zero.
B. ifits carbon content is very low.
C. if its hydrogen/hydrogen compound content is zero.
D. under no circumstances.
Show Answer
Scratch Pad
Discuss
Correct Answer: if its hydrogen/hydrogen compound content is zero.
7. The gas which contributes maximum to the heating value of natural gas is
Options
A. CO
B. CO
2
C. H
2
D. CH
4
Show Answer
Scratch Pad
Discuss
Correct Answer: CH
4
8. Low temperature carbonisation
Options
A. is mainly for producing the smokeless domestic coke.
B. is meant for the production of 'metallurgical coke'.
C. produces higher quantity of gas than high temperature carbonisation.
D. produces less quantity of tar than high temperature carbonisation.
Show Answer
Scratch Pad
Discuss
Correct Answer: is mainly for producing the smokeless domestic coke.
9. Presence of free moisture in coal during its high temperature carbonisation
Options
A. reduces the coking time.
B. protects the volatile products from pyrolysis (cracking) in the presence of hot coke and hot oven walls.
C. increases the loss of fine coal dust from the ovens when charging.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: protects the volatile products from pyrolysis (cracking) in the presence of hot coke and hot oven walls.
10. Natural draught produced by a chimney depends upon the
Options
A. density of the chimney gases.
B. height of the chimney.
C. both (a) and (b).
D. neither (a) nor (b).
Show Answer
Scratch Pad
Discuss
Correct Answer: both (a) and (b).
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry