CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Chemical Engineering Thermodynamics
Comments
Question
Measurement of thermodynamic property of temperature is facilitated by __________ law of thermodynamics.
Options
A. 1st
B. zeroth
C. 3rd
D. none of these
Correct Answer
zeroth
Chemical Engineering Thermodynamics problems
Search Results
1. Pick out the wrong statement.
Options
A. Activity co-efficient is dimensionless.
B. In case of an ideal gas, the fagacity is equal to its pressure.
C. In a mixture of ideal gases, the fugacity of a component is equal to the partial pressure of the component.
D. The fugacity co-efficient is zero for an ideal gas.
Show Answer
Scratch Pad
Discuss
Correct Answer: The fugacity co-efficient is zero for an ideal gas.
2. If the vapour pressure at two temperatures of a solid phase in equilibrium with its liquid phase are known, then the latent heat of fusion can be calculated by the
Options
A. Maxwell's equation
B. Clayperon-Claussius equation
C. Van Laar equation
D. Nernst Heat Theorem
Show Answer
Scratch Pad
Discuss
Correct Answer: Clayperon-Claussius equation
3. Compressibility factor for almost all the gases are approximately same at the same
Options
A. pressure and temperature.
B. reduced pressure and reduced temperature.
C. critical pressure and critical temperature.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: reduced pressure and reduced temperature.
4. Isobaric process means a constant process.
Options
A. temperature
B. pressure
C. volume
D. entropy
Show Answer
Scratch Pad
Discuss
Correct Answer: pressure
5. In a reversible chemical reaction (where, ?
x
= number of moles of products-number of moles of reactants )
Options
A. addition of inert gas favours the forward reaction, when ?
x
is positive.
B. pressure has no effect on equilibrium, when ?
n
= 0.
C. addition of inert gas has no effect on the equilibrium constant at constant volume for any value of ?
x
(+ ve, - ve) or zero).
D. all 'a', 'b' & 'c'.
Show Answer
Scratch Pad
Discuss
Correct Answer: all 'a', 'b' & 'c'.
6. No work is done by the system, when a reaction occurs at constant
Options
A. volume
B. temperature
C. pressure
D. none of these
Show Answer
Scratch Pad
Discuss
Correct Answer: volume
7. Out of the following refrigeration cycles, which one has maximum COP?
Options
A. Air cycle
B. Carnot cycle
C. Ordinary vapor compression cycle
D. Vapor compression with a reversible expansion engine
Show Answer
Scratch Pad
Discuss
Correct Answer: Carnot cycle
8. Maximum work that could be secured by expanding the gas over a given pressure range is the __________ work.
Options
A. isothermal
B. adiabatic
C. isentropic
D. none of these
Show Answer
Scratch Pad
Discuss
Correct Answer: isothermal
9. During Joule-Thomson expansion of gases
Options
A. enthalpy remains constant.
B. entropy remains constant.
C. temperature remains constant.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: enthalpy remains constant.
10. Which of the following is not used as a binder in coal briquetting?
Options
A. Tar
B. Molasses
C. Pitch
D. Line
Show Answer
Scratch Pad
Discuss
Correct Answer: Line
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry