CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Heat Transfer
Comments
Question
The equivalent diameter for pressure drop is __________ that for heat transfer.
Options
A. smaller than
B. greater than
C. equal to
D. not related with
Correct Answer
smaller than
Heat Transfer problems
Search Results
1. Air is best heated with steam in a heat exchanger of
Options
A. plate type.
B. double pipe type with fin on steam side.
C. double pipe type with fin on air side.
D. shell and tube type.
Show Answer
Scratch Pad
Discuss
Correct Answer: double pipe type with fin on air side.
2. Pick out the wrong statement.
Options
A. Orifice baffles are never used in a shell and tube heat exchanger.
B. Pressure drop on the shell side of a heat exchanger depends upon tube pitch also.
C. In a horizontal tube evaporator, surface blanketing by air is avoided.
D. Split ring type and pull through type floating heads are two commonly used floating heads is heat exchangers.
Show Answer
Scratch Pad
Discuss
Correct Answer: Orifice baffles are never used in a shell and tube heat exchanger.
3. Heat produced when a steady state current,
I
passes through an electrical conductor having resistance, '
R
' is
Options
A.
IR
B.
I
2
R
C.
IR
2
D.
I
2
R
2
Show Answer
Scratch Pad
Discuss
Correct Answer:
I
2
R
4. Fourier's law applies to the heat transfer by
Options
A. convection
B. radiation
C. conduction
D. all (a), (b) & (c)
Show Answer
Scratch Pad
Discuss
Correct Answer: conduction
5. Shell side pressure drop in a shell and tube heat exchanger does not depend upon the
Options
A. baffle spacing & shell diameter.
B. tube diameter & pitch.
C. viscosity, density & mass velocity of shell side fluid.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: none of these.
6. Which is the controlling factor for a drum drier?
Options
A. Diffusion
B. Heat transfer
C. Both (a) and (b)
D. Neither (a) nor (b)
Show Answer
Scratch Pad
Discuss
Correct Answer: Heat transfer
7. When the temperature and humidity of air is low, we usually use __________ draft cooling tower.
Options
A. natural
B. forced
C. induced
D. none of these
Show Answer
Scratch Pad
Discuss
Correct Answer: natural
8. Mass transfer rate between two fluid phases does not necessarily depend on the __________ of the two phases.
Options
A. chemical properties
B. physical properties
C. degree of turbulence
D. interfacial area
Show Answer
Scratch Pad
Discuss
Correct Answer: chemical properties
9. With increase in pressure, the relative volatility for a binary system
Options
A. increases.
B. decreases.
C. remains same.
D. either (a) or (b), depends on the system.
Show Answer
Scratch Pad
Discuss
Correct Answer: decreases.
10. In batch distillation with constant reflux, overhead product composition __________ with time.
Options
A. increases
B. decreases
C. does not vary
D. may increase on decrease, depends on the system.
Show Answer
Scratch Pad
Discuss
Correct Answer: decreases
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry