Discussion
Home ‣ Chemical Engineering ‣ Heat Transfer Comments
- Question
Controlling heat transfer film co-efficient is the one, which offers __________ resistance to heat transfer.
Options- A. no
- B. the least
- C. the largest
- D. lower
- Correct Answer
- the largest
- 1. The unit of heat transfer co-efficient in SI unit is
Options- A. J/M2°K
- B. W/m2°K
- C. W/m°K
- D. J/m°K Discuss
- 2. Air is to be heated by condensing steam. Two heat exchangers are available (i) a shell and tube heat exchanger and (ii) a finned tube heat exchanger. Tube side heat transfer area are equal in both the cases. The recommended arrangement is
Options- A. finned tube heat exchanger with air inside and steam outside.
- B. finned tube heat exchanger with air outside and steam inside.
- C. shell and tube heat exchanger with air inside tubes and steam on shell side.
- D. shell and tube heat exchanger with air on shell side and steam inside tubes. Discuss
- 3. The actual temperature drop across the heating surface in an evaporator depends on the
Options- A. feed.
- B. depth of liquid over heating surface.
- C. pressure difference between steam chest and vapour space.
- D. all (a), (b) and (c). Discuss
- 4. Baffles in the shell side of a shell and tube heat exchanger
Options- A. increase the cross-section of the shell side liquid.
- B. force the liquid to flow parallel to the bank.
- C. increase the shell side heat transfer co-efficient.
- D. decrease the shell side heat transfer co-efficient. Discuss
- 5. Bulk of the convective heat transfer resistance from a hot tube surface to the fluid flowing in it, is
Options- A. in the central core of the fluid.
- B. uniformly distributed throughout the fluid.
- C. mainly confined to a thin film of fluid near the surface.
- D. none of these. Discuss
- 6. Black liquor generated during paper manufacture is concentrated in a
Options- A. single effect evaporator.
- B. single effect evaporator followed by a crystalliser.
- C. multiple effect evaporator.
- D. multiple effect evaporators followed by a crystalliser. Discuss
- 7. Leidenfrost point is a term concerned with the
Options- A. condensation of the saturated vapor on a cold surface.
- B. concentration of a corrosive solution by evaporation.
- C. heat transfer between two highly viscous liquids.
- D. boiling of a liquid on a hot surface. Discuss
- 8. Reynold's analogy states that
Options- A. Nst ? f
- B. Nst ? NRe
- C. NNu ? f
- D. NRe ? f Discuss
- 9. Pick out the wrong statement.
Options- A. The controlling resistance in case of heating of air by condensing steam is in the air film.
- B. The log mean temperature difference (LMTD) for counter flow and parallel flow can be theoretically same when any one of the fluids (hot or cold fluid) passes through the heat exchanger at constant temperature.
- C. In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs.
- D. Phase change in case of a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature. Discuss
- 10. Which of the following is generally considered as opaque surface towards radiations?
Options- A. Gases
- B. Solids
- C. Liquids
- D. Both (b) and (c) Discuss
Heat Transfer problems
Search Results
Correct Answer: W/m2°K
Correct Answer: finned tube heat exchanger with air outside and steam inside.
Correct Answer: all (a), (b) and (c).
Correct Answer: increase the shell side heat transfer co-efficient.
Correct Answer: mainly confined to a thin film of fluid near the surface.
Correct Answer: multiple effect evaporator.
Correct Answer: boiling of a liquid on a hot surface.
Correct Answer: Nst ? f
Correct Answer: In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs.
Correct Answer: Both (b) and (c)
Comments
There are no comments.More in Chemical Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.