Discussion
Home ‣ Chemical Engineering ‣ Heat Transfer Comments
- Question
The number of kg vaporised per kg of steam fed to the evaporator is defined as
Options- A. capacity
- B. rate of evaporation
- C. economy
- D. rate of vaporisation
- Correct Answer
- economy
- 1. In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient
Options- A. increases
- B. decreases
- C. is not affected
- D. may increase or decrease; depends on the feed Discuss
- 2. Hot water (0.01 m3 /min) enters the tube side of a counter current shell and tube heat exchanger at 80°C and leaves at 50°C. Cold oil (0.05 m3/min) of density 800 kg/m3 and specific heat of 2 kJ/kg.K enters at 20°C. The log mean temperature difference in °C is approximately
Options- A. 32
- B. 37
- C. 45
- D. 50 Discuss
- 3. The heat flux (from outside to inside) across an insulating wall with thermal conductivity, K= 0.04 W/m.°K and thickness 0.16m is 10 W/m2. The temperature of the inside wall is - 5°C. The outside wall temperature is
Options- A. 25°C
- B. 30°C
- C. 35°C
- D. 40°C Discuss
- 4. In troposphere (the weather domain), the temperature 't' at height 'h' above the sea level in metres is given by (where, temperature at sea level is 15°C and t is in °C.)
Options- A. t = 15 - 0.0065 h
- B. t = 15 + 0.0065 h
- C. t = 0.0035 h - 15
- D. t = 15 - 0.0035 h Discuss
- 5. Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans?
Options- A. Emissivity of pipe surface.
- B. Diameter & length of the pipe.
- C. Temperature of hot pipe surface & that of air in the room.
- D. none of these. Discuss
- 6. For an ideal black body
Options- A. absorptivity = 1
- B. reflectivity = 1
- C. emissivity = 0
- D. transmissivity = 1 Discuss
- 7. In a heat exchanger, floating head is provided to
Options- A. facilitate cleaning of the exchanger.
- B. increase the heat transfer area.
- C. relieve stresses caused by thermal expansion.
- D. increase log mean temperature gradient. Discuss
- 8. When vaporisation takes place directly at the heating surface, it is called
Options- A. film boiling
- B. nucleate boiling
- C. vapour binding
- D. none of these Discuss
- 9. The steam ejector is used to
Options- A. remove condensate from the steam pipelines.
- B. create vacuum.
- C. superheat the steam.
- D. none of these. Discuss
- 10. In the equation Q = UA?t; ?t is
Options- A. geometric mean temperature difference.
- B. arithmetic mean temperature difference.
- C. logarithmic mean temperature difference.
- D. the difference of average bulk temperatures of hot and cold fluids. Discuss
Heat Transfer problems
Search Results
Correct Answer: decreases
Correct Answer: 32
Correct Answer: 35°C
Correct Answer: t = 15 - 0.0065 h
Correct Answer: none of these.
Correct Answer: absorptivity = 1
Correct Answer: relieve stresses caused by thermal expansion.
Correct Answer: nucleate boiling
Correct Answer: create vacuum.
Correct Answer: logarithmic mean temperature difference.
Comments
There are no comments.More in Chemical Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.