CuriousTab
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank Clerk
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Mechanical Engineering
‣
Workshop Technology
See What Others Are Saying!
Question
Thread rolling is restricted to
Options
A. ferrous materials
B. ductile materials
C. hard materials
D. none of these
Correct Answer
ductile materials
More questions
1. The wet bulb temperature at 100% relative humidity is __________ dew point temperature.
Options
A. same as
B. lower than
C. higher than
Show Answer
Scratch Pad
Discuss
Correct Answer: same as
2. Projection welding is a
Options
A. continuous spot welding process
B. multi-spot welding process
C. arc welding process
D. process used for joining round bars
Show Answer
Scratch Pad
Discuss
Correct Answer: multi-spot welding process
3. The error in discharge (
dQ
/
Q
) to the error in measurement of head (
dH
/
H
) over a rectangular notch is given by
Options
A.
B.
C.
D.
Show Answer
Scratch Pad
Discuss
Correct Answer:
4. The torque transmitted by a solid shaft of diameter (
D
) is (where ? = Maximum allowable shear stress)
Options
A.
x ? x
D
3
B.
x ? x
D
3
C.
x ? x
D
3
D.
x ? x
D
3
Show Answer
Scratch Pad
Discuss
Correct Answer:
x ? x
D
3
5. The unit discharge through the turbine is
Options
A.
B.
C.
D.
Show Answer
Scratch Pad
Discuss
Correct Answer:
6. The loud pulsating noise heard within the cylinder of an internal combustion engine is known as
Options
A. detonation
B. turbulence
C. pre-ignition
D. supercharging
Show Answer
Scratch Pad
Discuss
Correct Answer: detonation
7. Duralumin contains
Options
A. 3.5 to 4.5% copper, 0.4 to 0.7% magnesium, 0.4 to 0.7% manganese and rest aluminium
B. 3.5 to 4.5% copper, 1.2 to 1.7% managanese, 1.8 to 2.3% nickel, 0.6% each of silicon, magnesium and iron, and rest aluminium
C. 4 to 4.5% magnesium, 3 to 4% copper and rest aluminium
D. 5 to 6% tin, 2 to 3% copper and rest aluminium
Show Answer
Scratch Pad
Discuss
Correct Answer: 3.5 to 4.5% copper, 0.4 to 0.7% magnesium, 0.4 to 0.7% manganese and rest aluminium
8. The working pressure and temperature inside the cylinder of an internal combustion engine is __________ as compared to a steam engine.
Options
A. low
B. very low
C. high
D. very high
Show Answer
Scratch Pad
Discuss
Correct Answer: very high
9. The efficiency of the vane blower is (where
W
1
= Workdone due to compression, and
W
2
= Workdone due to back flow)
Options
A.
B.
C.
D.
Show Answer
Scratch Pad
Discuss
Correct Answer:
10. The ratio of the energy absorbed by the body to the total energy falling on it, is called
Options
A. absorptive power
B. emissive power
C. emissivity
D. none of these
Show Answer
Scratch Pad
Discuss
Correct Answer: absorptive power
Comments
There are no comments.
Enter a new Comment
Save
More in Mechanical Engineering:
Automobile Engineering
Compressors, Gas Dynamics and Gas Turbines
Engineering Materials
Engineering Mechanics
Heat Transfer, Refrigeration and Air Conditioning
Hydraulic Machines
Hydraulics and Fluid Mechanics
IC Engines and Nuclear Power Plants
Industrial Engineering and Production Management
Machine Design
Production Engineering
Steam Boilers and Engines
Steam Nozzles and Turbines
Strength of Materials
Theory of machines
Thermodynamics
Workshop Technology