CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Mechanical Engineering
‣
IC Engines and Nuclear Power Plants
Comments
Question
A diesel engine has
Options
A. one valve
B. two valves
C. three valves
D. four valves
Correct Answer
three valves
IC Engines and Nuclear Power Plants problems
Search Results
1. The nuclear power station at Tarapur has the reactor of the __________ type.
Options
A. pressurized water
B. boiling water
C. gas cooled
D. liquid metal cooled
Show Answer
Scratch Pad
Discuss
Correct Answer: boiling water
2. A carburettor is used to supply
Options
A. petrol, air and lubricating oil
B. air and diesel
C. petrol and lubricating oil
D. petrol and air
Show Answer
Scratch Pad
Discuss
Correct Answer: petrol and air
3. In a four stroke cycle petrol engine, the inlet valve
Options
A. opens at top dead centre and closes at bottom dead centre
B. opens at 20° before top dead centre and closes at 40° after bottom dead centre
C. opens at 20° after top dead centre and closes at 20° before bottom dead centre id) may open or close anywhere
Show Answer
Scratch Pad
Discuss
Correct Answer: opens at 20° before top dead centre and closes at 40° after bottom dead centre
4. Pre-ignition is caused by the spontantaneous combustion of the mixture before the end of the compression stroke, and is due to
Options
A. cylinder walls being too hot
B. overheated spark plug points
C. red hot carbon deposits on cylinder walls
D. any one of these
Show Answer
Scratch Pad
Discuss
Correct Answer: any one of these
5. The compensating jet in a carburettor supplies almost constant amount of petrol at all speeds because the
Options
A. jet area is automatically varied depending on the suction
B. the flow from the main jet is diverted to the compensating jet with increase in speed
C. the diameter of the jet is constant and the discharge coefficient is invariant
D. flow is produced due to the static head in the float chamber
Show Answer
Scratch Pad
Discuss
Correct Answer: flow is produced due to the static head in the float chamber
6. The pressure inside the cylinder is __________ the atmospheric pressure during the exhaust stroke.
Options
A. equal to
B. below
C. above
Show Answer
Scratch Pad
Discuss
Correct Answer: above
7. In open combustion chamber in diesel engines, the shape and layout of the piston crown, the inlet port and the valve produce the turbulent effect of fuel mixture.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
8. Nuclear reactors are used
Options
A. to produce heat for thermoelectric power
B. to produce fissionable material
C. to propel ships, submarines, aircrafts
D. all of these
Show Answer
Scratch Pad
Discuss
Correct Answer: all of these
9. The diesel engines are also known as __________ engines.
Options
A. compression ignition
B. spark ignition
Show Answer
Scratch Pad
Discuss
Correct Answer: compression ignition
10. The self ignition temperature of petrol is __________ as compared to diesel oil.
Options
A. same
B. lower
C. higher
Show Answer
Scratch Pad
Discuss
Correct Answer: higher
Comments
There are no comments.
Enter a new Comment
Save
More in Mechanical Engineering:
Automobile Engineering
Compressors, Gas Dynamics and Gas Turbines
Engineering Materials
Engineering Mechanics
Heat Transfer, Refrigeration and Air Conditioning
Hydraulic Machines
Hydraulics and Fluid Mechanics
IC Engines and Nuclear Power Plants
Industrial Engineering and Production Management
Machine Design
Production Engineering
Steam Boilers and Engines
Steam Nozzles and Turbines
Strength of Materials
Theory of machines
Thermodynamics
Workshop Technology