CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Computer Science
‣
Automation System
Comments
Question
Having compatibility and commonality in and between vendors' equipment is called:
Options
A. registration
B. standardization
C. integration
D. networking
E. None of the above
Correct Answer
standardization
Automation System problems
Search Results
1. The general CAD system was development by considering a wide range of possible uses of such a system.
Options
A. Mechanical engineering design
B. Animation and graphic design
C. Structural engineering design and Electronic circuit design
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: All of the above
2. A smart solid-state sensor is:
Options
A. one that integrates both logic and a solid-state sensor into one unit.
B. one that has two or three substrates
C. not available today
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: one that integrates both logic and a solid-state sensor into one unit.
3. An operating system:
Options
A. is required to run a microprocessor system
B. provides a structure with which to develop application programs
C. is useful because standard modules can be used
D. both (b) and (c)
E. None of the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: both (b) and (c)
4. Skipping every other line and picking up the skipped lines on the second pass is called:
Options
A. interlacing
B. refresh-vector
C. raster-scan
D. stroke writing
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: interlacing
5. The program execution time:
Options
A. must be slower than the fastest mechanical operation that is to be controlled
B. will vary depending on the language used
C. cannot be changed once the program is written
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: will vary depending on the language used
6. An up/down counter used in a TI510PC has three inputs. Which of the following is not one of them?
Options
A. Count up
B. Count out
C. Reset.
D. Count down
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Count out
7. The "end-effector" of a robot:
Options
A. can be an actual tool
B. is the robot "hand"
C. may have a gripping action
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: All of the above
8. Which of the following are kinds of instructions?
Options
A. Input
B. Arithmetic
C. Conditional branching
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: All of the above
9. Relay ladder logic is used in a PC because:
Options
A. it is impossible to write a control program for a machine in any other logic
B. it is the best industrial control language ever developed.
C. most industrial control personnel are familiar with relay ladder logic diagrams and this is the easiest for them to use
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: most industrial control personnel are familiar with relay ladder logic diagrams and this is the easiest for them to use
10. Which of the following is often used as an alternative to the light pen or in association with storage tube displays?
Options
A. Digitiser
B. Track ball
C. Mouse
D. Tablet
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Tablet
Comments
There are no comments.
Enter a new Comment
Save
More in Computer Science:
Artificial Intelligence
Automation System
Computer Fundamentals
Computer Hardware
Database Systems
Digital Computer Electronics
Disk Operating System (DOS)
Electronic Principles
Language Processors
Linux
Management Information Systems
Networking
Object Oriented Programming Using C++
Operating Systems Concepts
System Analysis and Design
Unix
Windows 2000 Server
Windows NT