CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Computer Science
‣
Automation System
Comments
Question
The program execution time:
Options
A. must be slower than the fastest mechanical operation that is to be controlled
B. will vary depending on the language used
C. cannot be changed once the program is written
D. All of the above
E. None of the above
Correct Answer
will vary depending on the language used
Automation System problems
Search Results
1. One advantage of a PC in industrial control is that it:
Options
A. has a reliable long life compared to relay logic
B. is very difficult for the inexperienced programmer to understand
C. is unreliable because there are no moving parts
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: has a reliable long life compared to relay logic
2. In the operation of a programmable controller:
Options
A. all of the logic status is maintained in memory
B. any latched data must be done using an external latching relay
C. mathematics cannot be performed
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: all of the logic status is maintained in memory
3. Which of the following is a graphical output device?
Options
A. Dot-matrix Printer
B. Plotter
C. Laser Printer
D. Line Printer
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Plotter
4. Ergonomics refers to:
Options
A. the human aspect of the environment around the workstation as well as the workstation itself
B. the cost relationship of the workstation versus productivity
C. the level of involvement the operator has with the workstation
D. the technology involved in the workstation itself
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: the human aspect of the environment around the workstation as well as the workstation itself
5. What is offset error?
Options
A. the difference between the sensor input and the absolute sensed parameter.
B. the difference between the controller output and the setting of the manipulated variable.
C. the difference between the control setpoint value and the actual value.
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: the difference between the control setpoint value and the actual value.
6. Skipping every other line and picking up the skipped lines on the second pass is called:
Options
A. interlacing
B. refresh-vector
C. raster-scan
D. stroke writing
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: interlacing
7. An operating system:
Options
A. is required to run a microprocessor system
B. provides a structure with which to develop application programs
C. is useful because standard modules can be used
D. both (b) and (c)
E. None of the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: both (b) and (c)
8. A smart solid-state sensor is:
Options
A. one that integrates both logic and a solid-state sensor into one unit.
B. one that has two or three substrates
C. not available today
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: one that integrates both logic and a solid-state sensor into one unit.
9. The general CAD system was development by considering a wide range of possible uses of such a system.
Options
A. Mechanical engineering design
B. Animation and graphic design
C. Structural engineering design and Electronic circuit design
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: All of the above
10. Having compatibility and commonality in and between vendors' equipment is called:
Options
A. registration
B. standardization
C. integration
D. networking
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: standardization
Comments
There are no comments.
Enter a new Comment
Save
More in Computer Science:
Artificial Intelligence
Automation System
Computer Fundamentals
Computer Hardware
Database Systems
Digital Computer Electronics
Disk Operating System (DOS)
Electronic Principles
Language Processors
Linux
Management Information Systems
Networking
Object Oriented Programming Using C++
Operating Systems Concepts
System Analysis and Design
Unix
Windows 2000 Server
Windows NT