CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Computer Science
‣
Automation System
Comments
Question
A continuous process is:
Options
A. used only for simple tasks
B. one that never shuts down
C. self-contained in that raw materials enter the process and an identifiable products exits the process.
D. used only with analog controllers.
E. None of the above
Correct Answer
self-contained in that raw materials enter the process and an identifiable products exits the process.
Automation System problems
Search Results
1. Who are called steel collar workers?
Options
A. Office clerks
B. Factory workers
C. Steel factory workers
D. Robots
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Robots
2. For a type 1 system, the steady-state:
Options
A. error for a step input is always zero
B. error for a velocity input is always zero
C. input for acceleration input is always non-zero
D. (a) and (c)
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: (a) and (c)
3. Microcomputer-based control sys¬tems
Options
A. will just keep their present capability
B. will have more standard industrial application software available in the future.
C. will tend to increase in cost.
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: will have more standard industrial application software available in the future.
4. A microprocessor:
Options
A. is another name for a computer
B. is a CPU in integrated circuit form
C. executes a program of instructions
D. (a) and (c)
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: (a) and (c)
5. The speed at which the monitor accepts data is called:
Options
A. bandwidth
B. response time
C. interlacing
D. scanning
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: bandwidth
6. How is the integral mode implemented on a digital controller?
Options
A. the digital controller cannot handle integral mode
B. the error is divided into discrete amounts
C. the error signal is summed over a discrete time interval and accumulated by the controller
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: the error signal is summed over a discrete time interval and accumulated by the controller
7. One of the major benefits of using CAD in tool design is that:
Options
A. product design represents approximately one-half the engineering costs
B. tool motions can be checked to see if there is interference between the tool and the object
C. there is better coordination in the materials-handling area
D. it simplifies the trial-and-error method
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: tool motions can be checked to see if there is interference between the tool and the object
8. For a type 0 system, the steady-state:
Options
A. error for a step input is always zero
B. error for a velocity input is always zero
C. input for acceleration input is always non-zero
D. (a) and (c)
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: input for acceleration input is always non-zero
9. Which of the following is required for a plotter to perform specific commands?
Options
A. Firmware
B. Software
C. Driver
D. Hardware
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Driver
10. Which of the following elements can be used with a TI510 FC?
Options
A. Drum timer
B. Metronome
C. Cymbal timer
D. Flashing light
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Drum timer
Comments
There are no comments.
Enter a new Comment
Save
More in Computer Science:
Artificial Intelligence
Automation System
Computer Fundamentals
Computer Hardware
Database Systems
Digital Computer Electronics
Disk Operating System (DOS)
Electronic Principles
Language Processors
Linux
Management Information Systems
Networking
Object Oriented Programming Using C++
Operating Systems Concepts
System Analysis and Design
Unix
Windows 2000 Server
Windows NT