logo

CuriousTab

CuriousTab

Discussion


Home Computer Science Windows NT See What Others Are Saying!
  • Question
  • Your 10Base2 Ethernet cable is 185 meters long. You are planning to extend your network by adding another 100 meters of cable. The total length of the cable will be 285 meters. The network uses NetBEUI. Which device should you use?


  • Options
  • A. repeater
  • B. T connecter
  • C. router
  • D. gateway
  • E. None of the above

  • Correct Answer
  • repeater 


  • More questions

    • 1. Which of the following systems implementation approaches should be used if you want to run the old system and the new system at the same time for a specified period?

    • Options
    • A. direct
    • B. pilot
    • C. phased
    • D. parallel
    • E. None of the above
    • Discuss
    • 2. In his landmark book Cybernetics, Norbert Wiener suggested a way of modeling scientific phenomena using not energy, but:

    • Options
    • A. mathematics
    • B. intelligence
    • C. information
    • D. history
    • E. None of the above
    • Discuss
    • 3. RTS stands for:

    • Options
    • A. ready to start
    • B. ready to switch
    • C. request to send
    • D. request to scan
    • E. ready to set
    • Discuss
    • 4. A programmable controller:

    • Options
    • A. allows faster machine checkout
    • B. is easier to troubleshoot than standard relay logic
    • C. both (a) and (b)
    • D. All of the above
    • E. None of the above
    • Discuss
    • 5. A battery is a device composed of one or more:

    • Options
    • A. chemical cells
    • B. voltage generators
    • C. solar cells
    • D. piezoeletric cells
    • E. None of the above
    • Discuss
    • 6. Convert the 080D4E machine language instructions into assembly language, assuming that they were not generated by pseudo-ops:

    • Options
    • A. ASRA
    • B. LOADA h#OD4E, i
    • C. STOREA h#014B, d
    • D. ADDA h#01FE, i
    • Discuss
    • 7. The packaged design includes all of the following except;

    • Options
    • A. program flowcharts
    • B. system configuration
    • C. module descriptions
    • D. All of the above
    • E. None of the above
    • Discuss
    • 8. After doing a low-level format, what would be the next step in configuring the hard drive in a system?

    • Options
    • A. Format DOS partition
    • B. Install operating system
    • C. Configure DMA channel and back up interrupt
    • D. Partition hard disk
    • E. None of the above
    • Discuss
    • 9. You are installing an IDE hard drive that will be your boot drive. Which is the correct order of steps that need to be followed?

    • Options
    • A. jumper properly, auto-detect(or configure manually) in CMOS, low level format, high level format, partition
    • B. jumper properly, auto-detect(or configure manually) in CMOS, partition, high level format with / s switch
    • C. jumper properly, partition, auto-detect(or configure manually in CMOS, high level format with /s switch
    • D. jumper properly, auto-detect in CMOS, regular format
    • E. jumper properly, partition, low level format, high level format
    • Discuss
    • 10. Related fields in a data base are grouped to form

    • Options
    • A. data file
    • B. data record
    • C. menu
    • D. bank
    • E. None of the above
    • Discuss


    Comments

    There are no comments.

Enter a new Comment