CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Computer Science
‣
Computer Hardware
Comments
Question
What is modified when changing the system start-up boot sequence?
Options
A. BIOS/CMOS
B. CONFIG.SYS
C. autoexec.bat
D. COMMAND.COM
E. None of the above
Correct Answer
BIOS/CMOS
Computer Hardware problems
Search Results
1. During the laser printer's conditioning phase a uniform charge of _____ is placed on the photosensitive drum.
Options
A. +1000 volt
B. +600 volts
C. -600 volts
D. -1000 volts
E. + 12 volts
Show Answer
Scratch Pad
Discuss
Correct Answer: -600 volts
2. To prevent toner from sticking to a laser printer's heat rollers, apply which of the following:
Options
A. Alcohol
B. Oil
C. Ammonia
D. Beer or Jack Daniels
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Oil
3. When configuring is a network interface cards without jumpers or plug and play, what is used to set the IRQs?
Options
A. DMA
B. CMOS
C. the OS
D. configuration software
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: configuration software
4. In which mode can 2 or more applications be stored in memory at the same time?
Options
A. Segmented Mode
B. Unprotected Mode
C. Real Mode
D. Protected Mode
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Protected Mode
5. After trying to unload a TSR, you get an error message saying that other TSRs were loaded after the one you tried to remove. Which of the following commands could you use to see the current load order?
Options
A. MEM /P
B. MEMMAKER
C. MEM /C (A SYS:
D. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: MEM /C (A SYS:
6. After doing a low-level format, what would be the next step in configuring the hard drive in a system?
Options
A. Format DOS partition
B. Install operating system
C. Configure DMA channel and back-up interrupt
D. Partition hard disk
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Partition hard disk
7. What is the best ground for a conductive work bench?
Options
A. AC outlet
B. Ground to bend
C. To another device
D. Chassis ground
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: AC outlet
8. Match the device driver HIMEM.SYS to its operation.
Options
A. Supports (ANSI) terminal emulation
B. Manages the use of extended memory
C. Uses expanded memory on a 80386 processor
D. Supports code page switching
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Manages the use of extended memory
9. To find out how much memory is available, you could type _____
Options
A. EMM
B. MEM
C. CHKDSK
D. MEMMAKER
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: MEM
10. You suspect a virus has entered your computer. What will not be affected by the virus?
Options
A. CMOS
B. Boot sector
C. Floppy disks
D. Program files
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: CMOS
Comments
There are no comments.
Enter a new Comment
Save
More in Computer Science:
Artificial Intelligence
Automation System
Computer Fundamentals
Computer Hardware
Database Systems
Digital Computer Electronics
Disk Operating System (DOS)
Electronic Principles
Language Processors
Linux
Management Information Systems
Networking
Object Oriented Programming Using C++
Operating Systems Concepts
System Analysis and Design
Unix
Windows 2000 Server
Windows NT