logo

CuriousTab

CuriousTab

Discussion


Home Computer Science Computer Hardware Comments

  • Question
  • In which mode can 2 or more applications be stored in memory at the same time?


  • Options
  • A. Segmented Mode
  • B. Unprotected Mode
  • C. Real Mode
  • D. Protected Mode
  • E. None of the above

  • Correct Answer
  • Protected Mode 


  • Computer Hardware problems


    Search Results


    • 1. After trying to unload a TSR, you get an error message saying that other TSRs were loaded after the one you tried to remove. Which of the following commands could you use to see the current load order?

    • Options
    • A. MEM /P
    • B. MEMMAKER
    • C. MEM /C (A SYS:
    • D. None of the above
    • Discuss
    • 2. How many pins on a VGA?

    • Options
    • A. 15.
    • B. 9
    • C. 25
    • D. 32
    • E. None of the above
    • Discuss
    • 3. To install a second IDE drive into a computer, you must:

    • Options
    • A. Set the master-slave jumper to slave on the second drive
    • B. Use the IDE configuration software to set the new drive as slave
    • C. Verify that you define the new drive as D: in the CMOS setup
    • D. Verity that you attach the drive to the connector at the end of the ribbon cable
    • E. None of the above
    • Discuss
    • 4. In which phase of the laser printing process is a positive charge placed on the paper to pull the toner from the print drum?

    • Options
    • A. Writing
    • B. Transferring
    • C. Conditioning
    • D. All of the above
    • E. None of the above
    • Discuss
    • 5. When connecting a ribbon cable to a connector, how do you know which direction to plug it in?

    • Options
    • A. The red line in the cable goes to the highest pin number
    • B. The colored line in the cable goes to pin #1
    • C. It does not matter
    • D. The blue or red line in the cable goes away from the power connector
    • E. None of the above
    • Discuss
    • 6. When configuring is a network interface cards without jumpers or plug and play, what is used to set the IRQs?

    • Options
    • A. DMA
    • B. CMOS
    • C. the OS
    • D. configuration software
    • E. None of the above
    • Discuss
    • 7. To prevent toner from sticking to a laser printer's heat rollers, apply which of the following:

    • Options
    • A. Alcohol
    • B. Oil
    • C. Ammonia
    • D. Beer or Jack Daniels
    • E. None of the above
    • Discuss
    • 8. During the laser printer's conditioning phase a uniform charge of _____ is placed on the photosensitive drum.

    • Options
    • A. +1000 volt
    • B. +600 volts
    • C. -600 volts
    • D. -1000 volts
    • E. + 12 volts
    • Discuss
    • 9. What is modified when changing the system start-up boot sequence?

    • Options
    • A. BIOS/CMOS
    • B. CONFIG.SYS
    • C. autoexec.bat
    • D. COMMAND.COM
    • E. None of the above
    • Discuss
    • 10. After doing a low-level format, what would be the next step in configuring the hard drive in a system?

    • Options
    • A. Format DOS partition
    • B. Install operating system
    • C. Configure DMA channel and back-up interrupt
    • D. Partition hard disk
    • E. None of the above
    • Discuss


    Comments

    There are no comments.

Enter a new Comment