CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Computer Science
‣
Computer Hardware
Comments
Question
When configuring a new network interface card for installation, which of the following would be a valid I/O address?
Options
A. 378
B. 2F8
C. 3F8
D. 360
E. None of the above
Correct Answer
360
Computer Hardware problems
Search Results
1. If a computer's BIOS allows it, you can boot from a CD-ROM.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
2. ESD damage can be caused by:
Options
A. Placing an IC in a non-conductive plastic bag
B. Placing an IC on a grounded mat
C. Repeated sags in current supplied from outlets
D. Touching metal on the chasis
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Placing an IC in a non-conductive plastic bag
3. Which provides the fastest data access time?
Options
A. RAM
B. ROM
C. CD-ROM
D. Hard disk
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: RAM
4. Which best describes a fragmented hard drive:
Options
A. The platters are bad
B. Data files are corrupted
C. Clusters of data are damaged
D. Files are not stored in consecutive clusters
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Files are not stored in consecutive clusters
5. To test for AC ripple on a PC power supply, you would set the volt/ohm meter for:
Options
A. DC voltage scale
B. AC voltage
C. OHM scale
D. Farad scale
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: AC voltage
6. What is the jumper setting on a SCSI device to configure it to use the fourth SCSI id? Remember, SCSI ids start with zero.
Options
A. 010
B. 110
C. 011
D. 101
E. 001
Show Answer
Scratch Pad
Discuss
Correct Answer: 011
7. What problem can occur if a printer cable is to close to a power cable?
Options
A. ESD Electrostatic Discharge
B. EMI Electromagnetic Interference
C. parity error
D. no affect
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: EMI Electromagnetic Interference
8. You are testing the resistance in Ohms of a fuse on a 5 amp system. If the fuse is good, the meter should read?
Options
A. 5.0
B. 0.5
C. 0.0
D. All of the above
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: 0.0
9. The acronym HDI stands for:
Options
A. Half duplex interface
B. Hard disk interface
C. Head to disk interference
D. Help desk interference
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Help desk interference
10. COM 4 uses which I/O port?
Options
A. 2F8H
B. 3F8H
C. 3E8H
D. 2E8H
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: 2E8H
Comments
There are no comments.
Enter a new Comment
Save
More in Computer Science:
Artificial Intelligence
Automation System
Computer Fundamentals
Computer Hardware
Database Systems
Digital Computer Electronics
Disk Operating System (DOS)
Electronic Principles
Language Processors
Linux
Management Information Systems
Networking
Object Oriented Programming Using C++
Operating Systems Concepts
System Analysis and Design
Unix
Windows 2000 Server
Windows NT