CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Computer Science
‣
Computer Hardware
Comments
Question
Resistance is measured in units of:
Options
A. ohms
B. farads
C. helids
D. amperes
E. volts
Correct Answer
ohms
Computer Hardware problems
Search Results
1. COM1 is typically represented by which of the following?
Options
A. 15 pin port
B. 9 pin male port
C. 9 pin female port
D. 25 pin male port
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: 9 pin male port
2. A capacitor is measured in which of the following units?
Options
A. Volts
B. Ohms
C. Farads
D. Resistance
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: Farads
3. IDE cables have how many pins?
Options
A. 25
B. 50
C. 100
D. 40
E. 65
Show Answer
Scratch Pad
Discuss
Correct Answer: 40
4. How many DMA channels are there in an AT class PC?
Options
A. 3
B. 4
C. 7
D. 8
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: 8
5. What should you replace if the brightness or contrast adjustments were malfunctioning on a laptop?
Options
A. fuse
B. led display
C. adjustment switch
D. led display cable
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: led display
6. ESD potential decreases with the use of:
Options
A. De-ionizing fans
B. A wrist strap
C. Rubber gloves with matching cap
D. A static meter
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: A wrist strap
7. What voltage does a 586 system use?
Options
A. +12 volts
B. + 5 volts
C. + 8 volts
D. +3.3 volts
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: + 5 volts
8. An important first step in troubleshooting which component in a laser printer is causing a jam is to:
Options
A. note where in the paper path the paper stops
B. check all voltages
C. look up error codes
D. turn the printer off, then on again
E. remove the jammed paper
Show Answer
Scratch Pad
Discuss
Correct Answer: note where in the paper path the paper stops
9. A static jolt of as little of _____ volts can fry most any PC integrated circuit.
Options
A. 200
B. 30
C. 1000
D. 200
E. 500
Show Answer
Scratch Pad
Discuss
Correct Answer: 30
10. During the normal PC boot process, which of the following is active first?
Options
A. RAM BIOS
B. CMOS
C. ROM BIOS
D. Hard disk information
E. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: ROM BIOS
Comments
There are no comments.
Enter a new Comment
Save
More in Computer Science:
Artificial Intelligence
Automation System
Computer Fundamentals
Computer Hardware
Database Systems
Digital Computer Electronics
Disk Operating System (DOS)
Electronic Principles
Language Processors
Linux
Management Information Systems
Networking
Object Oriented Programming Using C++
Operating Systems Concepts
System Analysis and Design
Unix
Windows 2000 Server
Windows NT