Discussion
Home ‣ Computer Science ‣ Computer Hardware Comments
- Question
How many devices can be used on a single SCSI bus? Keep in mind that the SCSI host adapter counts as a device.
Options- A. 1
- B. 8
- C. 20
- D. 10
- E. All of the above
- Correct Answer
- 8
- 1. Match the device driver HIMEM.SYS to its operation.
Options- A. Supports (ANSI) terminal emulation
- B. Manages the use of extended memory
- C. Uses expanded memory on a 80386 processor
- D. Supports code page switching
- E. None of the above Discuss
- 2. When connecting two internal SCSI hard disks to a computer, where do you connect the second hard drive?
Options- A. Any open SCSI port on the computer
- B. A Serial port on the first host adapter
- C. An open parallel port on the computer
- D. An open SCSI port on the first hard drive
- E. None of the above Discuss
- 3. Which component must be vacuumed or replaced during preventative maintenance on a laser printer?
Options- A. Scanning mirror
- B. Toner cartridge
- C. Ozone filter
- D. All of the above
- E. None of the above Discuss
- 4. What's the best way to prevent damaging your PC with static electricity?
Options- A. place your PC on a rubber mat
- B. wear leather soled shoes
- C. periodically touch a safe ground point on the PC to discharge yourself
- D. static electricity doesn't really hurt a PC
- E. wear an ESD wrist strap Discuss
- 5. On the 16-bit ISA bus, IRQ2 is elevated to which higher level interrupt?
Options- A. 9
- B. 11
- C. 13
- D. 15
- E. None of the above Discuss
- 6. Which of the following would be a logical first step in troubleshooting a PC?
Options- A. Check the computer CMOS
- B. Define the circumstances of the problem
- C. Call the vendor
- D. Define what applications are being used
- E. None of the above Discuss
- 7. On a dot matrix printer, you should never lubricate which part?
Options- A. carriage rails
- B. printhead pins
- C. paper advance bearings
- D. carriage bearings
- E. None of the above Discuss
- 8. The digital multimeter is set for DC, Ohm and 20k. You will read _____ while measuring a good 2 amp fuse.
Options- A. 0.00
- B. 0.02
- C. 0.20
- D. 2.00
- E. None of the above Discuss
- 9. To install a second IDE drive into a computer, you must:
Options- A. Set the master-slave jumper to slave on the second drive
- B. Use the IDE configuration software to set the new drive as slave
- C. Verify that you define the new drive as D: in the CMOS setup
- D. Verify that you attach the drive to the connector at the end of the ribbon cable
- E. None of the above Discuss
- 10. Which of the following FRUs would be considered both an input/output device?
Options- A. Video board
- B. SCSI host adapter
- C. System board CPU
- D. All of the above
- E. None of the above Discuss
Computer Hardware problems
Search Results
Correct Answer: Manages the use of extended memory
Correct Answer: Any open SCSI port on the computer
Correct Answer: Ozone filter
Correct Answer: wear an ESD wrist strap
Correct Answer: 9
Correct Answer: Define the circumstances of the problem
Correct Answer: printhead pins
Correct Answer: 0.00
Correct Answer: Set the master-slave jumper to slave on the second drive
Correct Answer: SCSI host adapter
Comments
There are no comments.More in Computer Science:
Programming
Copyright ©CuriousTab. All rights reserved.