CuriousTab

Home Aptitude

Discussion

Home ‣ Electronics and Communication Engineering ‣ Matching Questions Comments

Question

Match the following:

List I (Functional components) List II (Device)

A. Error detector 1. Three phase FHP Induction motor

B. Servo motor 2. Synchro transmitter and control transformer

C. Amplifier 3. Tacho generator

D. Feed back 4. Armature controlled FHP dc motor

5. Amplidyne

Options
A. A-2, B-4, C-1, D-5
B. A-4, B-2, C-5, D-3
C. A-2, B-4, C-5, D-3
D. A-1, B-2, C-3, D-5

	List I (Functional components)		List II (Device)
A.	Error detector	1.	Three phase FHP Induction motor
B.	Servo motor	2.	Synchro transmitter and control transformer
C.	Amplifier	3.	Tacho generator
D.	Feed back	4.	Armature controlled FHP dc motor
		5.	Amplidyne

Correct Answer

A-2, B-4, C-5, D-3

Matching Questions problems

Search Results

1. Match the following:

	List I (Instruction)		List II (Flag's getting affected)
A.	ORI	1.	CY reset
B.	DAA	2.	CY reset and AC reset
C.	PCHIL	3.	S, Z, AC, P, CY flags affected
		4.	S, S, P are modified
		5.	No flags affected

Options
A. A-2, B-3, C-5
B. A-4, B-3, C-5
C. A-1, B-2, C-3
D. A-2, B-4, C-1

Discuss

	List I (Branches)		List II
A.	1, 2, 3, 4	1.	Twigs
B.	4, 5, 6, 7	2.	Links
C.	1, 2, 3, 8	3.	Fundamental cutset
D.	1, 4, 5, 6, 7	4.	Fundamental loop

Options
A. A-3, B-1, C-2, D-4
B. A-2, B-3, C-1, D-4
C. A-3, B-2, C-4, D-1
D. A-1, B-4, C-3, D-2

Discuss

3. Match the following:

	List I		List II
A.	Coastals receiver	1.	VSB
B.	Stereo-multiplexing	2.	Demodulating DSB-SC
C.	TV broad casting	3.	FM radio broad casting
		4.	Slope overload
		5.	Matched filter

Options
A. A-1, B-3, C-2
B. A-2, B-3, C-1
C. A-2, B-1, C-4
D. A-4, B-3, C-1

Discuss

4. Match the following:

	List I		List II
A.	Ratio of maximum energy stored to energy dissipated per cycle	1.	Propagation constant
B.	TEM mode is loss less medium	2.	Cutoff frequency is zero
C.	Ratio of frequency in radian to phase velocity of EM wave	3.	Quality factor of cavity
D.	TEM is the mode of lowest cutoff frequency	4.	Cylindrical waveguide

Options
A. A-3, B-2, C-4, D-1
B. A-2, B-3, C-1, D-4
C. A-3, B-2, C-1, D-4
D. A-2, B-3, C-4, D-1

Discuss

5. Match the following:

		List II
A.	1.	Band reject (notch) filter
B.	2.	Band pass filter
C.	3.	High pass filter
D.	4.	Low pass filters

Options
A. A-3, B-4, C-2, D-1
B. A-3, B-4, C-1, D-2
C. A-4, B-3, C-1, D-2
D. A-4, B-3, C-2, D-1

Discuss

6. Match the following:

	List I
A.	NPN transistor	1.
B.	PNP transistor	2.
C.	n channel JFET	3.
D.	p channel JFET	4.

Options
A. A-1, B-2, C-3, D-4
B. A-3, B-4, C-2, D-1
C. A-4, B-2, C-1, D-3
D. A-1, B-2, C-4, D-3

Discuss

7. If r is resistivity, l is length of wire, a is area of cross-section, ? is angular frequency, F is form factor, n is number of turns, d is coil diameter and r is resistance of a coil.