logo

CuriousTab

CuriousTab

Discussion

Home ‣ Electronics and Communication Engineering ‣ Matching Questions Comments
  • Question

  • Match the following:

    List I (Instruction) List II (Flag's getting affected)
    A. ORI 1. CY reset
    B. DAA 2. CY reset and AC reset
    C. PCHIL 3. S, Z, AC, P, CY flags affected
    4. S, S, P are modified
    5. No flags affected


  • Options
  • A. A-2, B-3, C-5
  • B. A-4, B-3, C-5
  • C. A-1, B-2, C-3
  • D. A-2, B-4, C-1

  • Correct Answer
  • A-4, B-3, C-5 

    • Matching Questions problems

    Search Results

    • 1. 

      List I (Branches) List II
      A. 1, 2, 3, 4 1. Twigs
      B. 4, 5, 6, 7 2. Links
      C. 1, 2, 3, 8 3. Fundamental cutset
      D. 1, 4, 5, 6, 7 4. Fundamental loop


    • Options
    • A. A-3, B-1, C-2, D-4
    • B. A-2, B-3, C-1, D-4
    • C. A-3, B-2, C-4, D-1
    • D. A-1, B-4, C-3, D-2
      • Discuss
    • 2. Match the following:

      List I List II
      A. Coastals receiver 1. VSB
      B. Stereo-multiplexing 2. Demodulating DSB-SC
      C. TV broad casting 3. FM radio broad casting
      4. Slope overload
      5. Matched filter


    • Options
    • A. A-1, B-3, C-2
    • B. A-2, B-3, C-1
    • C. A-2, B-1, C-4
    • D. A-4, B-3, C-1
      • Discuss
    • 3. Match the following:

      List I List II
      A. Ratio of maximum energy stored to energy dissipated per cycle 1. Propagation constant
      B. TEM mode is loss less medium 2. Cutoff frequency is zero
      C. Ratio of frequency in radian to phase velocity of EM wave 3. Quality factor of cavity
      D. TEM is the mode of lowest cutoff frequency 4. Cylindrical waveguide


    • Options
    • A. A-3, B-2, C-4, D-1
    • B. A-2, B-3, C-1, D-4
    • C. A-3, B-2, C-1, D-4
    • D. A-2, B-3, C-4, D-1
      • Discuss
    • 4. Match the following:

      List I List II
      A. 1. Band reject (notch) filter
      B. 2. Band pass filter
      C. 3. High pass filter
      D. 4. Low pass filters


    • Options
    • A. A-3, B-4, C-2, D-1
    • B. A-3, B-4, C-1, D-2
    • C. A-4, B-3, C-1, D-2
    • D. A-4, B-3, C-2, D-1
      • Discuss
    • 5. Match the following:

      List I (Signal) List II (Value)
      A. AM 1. 0 0.5
      B. DSB - SC 2. 1
      C. SSB 3. 2
      D. FM (? = 2) 4. 16
      E. FM (? = 5) 5. 8


    • Options
    • A. A-1, B-3, C-2, D-5, E-4
    • B. A-3, B-3, C-1, D-5, E-4
    • C. A-2, B-1, C-4, D-5, E-5
    • D. A-4, B-2, C-5, D-3, E-1
      • Discuss
    • 6. Match the following:

      List I (Functional components) List II (Device)
      A. Error detector 1. Three phase FHP Induction motor
      B. Servo motor 2. Synchro transmitter and control transformer
      C. Amplifier 3. Tacho generator
      D. Feed back 4. Armature controlled FHP dc motor
      5. Amplidyne


    • Options
    • A. A-2, B-4, C-1, D-5
    • B. A-4, B-2, C-5, D-3
    • C. A-2, B-4, C-5, D-3
    • D. A-1, B-2, C-3, D-5
      • Discuss
    • 7. Match the following:

      List I List II
      A. NPN transistor 1.
      B. PNP transistor 2.
      C. n channel JFET 3.
      D. p channel JFET 4.


    • Options
    • A. A-1, B-2, C-3, D-4
    • B. A-3, B-4, C-2, D-1
    • C. A-4, B-2, C-1, D-3
    • D. A-1, B-2, C-4, D-3
      • Discuss
    • 8. If r is resistivity, l is length of wire, a is area of cross-section, ? is angular frequency, F is form factor, n is number of turns, d is coil diameter and r is resistance of a coil.

      List I List II
      A. Value of inductance 1.
      B. Power factor 2.
      C. Q factor 3.
      D. Value of resistance 4. Fn2d


    • Options
    • A. A-1, B-2, C-3, D-4
    • B. A-4, B-3, C-2, D-1
    • C. A-4, B-2, C-3, D-1
    • D. A-1, B-3, C-2, D-4
      • Discuss
    • 9. Match the following:

      List I List II
      A. On-off 1. steam kettle with different settings
      B. Proportional 2. Elevator
      C. Cascade 3. Robot-positioning
      D. Digital 4. Domestic Refrigerator


    • Options
    • A. A-4, B-2, C-3, D-1
    • B. A-2, B-4, C-1, D-3
    • C. A-3, B-1, C-4, D-2
    • D. A-4, B-2, C-1, D-3
      • Discuss
    • 10. Match the following:

      List I List II
      A. Resistance 1. M-1L-2T4I2
      B. Inductance 2. ML2T-2I-2
      C. Capacitance 3. ML2T-3I2


    • Options
    • A. A-1, B-2, C-3
    • B. A-2, B-1, C-3
    • C. A-2, B-3, C-1
    • D. A-3, B-2, C-1
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.