CuriousTab

CuriousTab

Home Aptitude

Discussion

Home ‣ Electronics and Communication Engineering ‣ Matching Questions Comments

Question

Match the following:

List I List II

A. Mu Metal 1. very high magnetic permeability

B. Samrium/cobalt 2. very high magnetic remanence

C. Sapphire 3. very high thermal conductivity

D. Ferrites 4. very stable magnetic permeability

Options
A. A-1, B-2, C-3, D-4
B. A-3, B-4, C-1, D-2
C. A-2, B-3, C-4, D-1
D. A-4, B-1, C-2, D-3

Correct Answer

A-4, B-1, C-2, D-3

Matching Questions problems

Search Results

1. Match the following:

	List I		List II
A.	Detection of a periodic signal in noise	1.	Increase in bandwidth
B.	Recovery of a band limited signal from its uniformly sampled values	2.	Slope overload error
C.	Finer quantization of signal	3.	Nyquist rate
D.	Delta modulation	4.	Cross correlation

Options
A. A-4, B-3, C-1, D-2
B. A-3, B-4, C-2, D-1
C. A-4, B-3, C-2, D-1
D. A-4, B-2, C-1, D-3

2. Match the following:

	List I		List II
A.	Step up chopper	1.
B.	Class E chopper	2.
C.	Class D chopper	3.
D.	Class B chopper	4.

Options
A. A-1, B-3, C-4, D-2
B. A-3, B-1, C-4, D-2
C. A-1, B-2, C-3, D-4
D. A-4, B-2, C-1, D-3

3. Match the following:

List I List II

A. BJT 1.

B. SCR 2.

C. UJT 3.

D. PUT 4.
Options
A. A-1, B-2, C-3, D-4
B. A-2, B-3, C-1, D-4
C. A-1, B-3, C-4, D-2
D. A-4, B-2, C-1, D-3

4. Match the following:

	List I (Processor in C)		List II (Output)
A.	Preprocessor	1.	Source code file
B.	Compiler	2.	Executable code in machine language
C.	Linker	3.	Relocatable object code

Options
A. A-1, B-2, C-3
B. A-2, B-3, C-1
C. A-3, B-2, C-1
D. A-1, B-3, C-2

5. Match the following:

	List I (Circuits)		List II (Output dc voltage)
A.	Single phase half wave converter	1.
B.	Fully controlled bridge converter (1 phase) with RLE load	2.
C.	3 Phase full converter	3.
D.	Single phase full wave converter (M-2) connection	4.

Options
A. A-1, B-2, C-3, D-4
B. A-4, B-3, C-1, D-2
C. A-4, B-2, C-3, D-1
D. A-1, B-2, C-4, D-3

6. Match the following:

	List I (Types of N-bit ADC)		List II (Characteristics)
A.	Flash converter	1.	Integrating Type
B.	Successive	2.	Fastest converter approximation
C.	Counter ramp	3.	Maximum conversion time = N bits
D.	Dual slow	4.	Used a DAC in its feedback path

Options
A. A-2, B-3, C-4, D-1
B. A-1, B-3, C-4, D-2
C. A-2, B-4, C-3, D-1
D. A-1, B-4, C-3, D-2

7. Match the following:

	List I (Binary)		List II (Hexadecimal)
A.	10101010	1.	FF
B.	11111111	2.	88
C.	10001000	3.	92
D.	10010010	4.	AA

Options
A. A-4, B-1, C-2, D-3
B. A-1, B-2, C-3, D-4
C. A-3, B-1, C-2, D-4
D. A-1, B-3, C-4, D-1

8.

	List I (Theorems)		List II (Property of Network)
A.	h₁₁	1.	1/(r_e + r_d)
B.	h₁₂	2.	r_b + r_e
C.	h₂₁	3.	?_bc
D.	h₂₂	4.	?_cb

Options
A. A-2, B-1, C-4, D-3
B. A-4, B-3, C-2, D-1
C. A-2, B-3, C-4, D-1
D. A-4, B-1, C-2, D-3

9. Match the following:

	List I		List II
A.	IF amplifier	1.	Amplifier frequencies in the range of 100 kHz to 5 MHz.
B.	RF amplifier	2.	Current in the output flows only during a portion of the positive half of the input cycle
C.	AF amplifier	3.	Amplifier frequencies in the range of 0 Hz to 5 MHz
D.	Class operation	4.	Amplifier frequencies in the frequency range of 40 Hz to 15 kHz.

Options
A. A-4, B-1, C-3, D-2
B. A-3, B-1, C-4, D-2
C. A-2, B-3, C-1, D-4
D. A-1, B-2, C-3, D-4

10. Match the following:

	List I		List II
A.	Television	1.	Either AM or FM used
B.	Radio	2.	Both AM and FM are used
C.	Radar	3.	PCM is used
D.	Data Communication	4.	Digital system

Options
A. A-4, B-3, C-1, D-2
B. A-2, B-1, C-3, D-4
C. A-4, B-1, C-3, D-2
D. A-2, B-3, C-1, D-4

Comments

More in Electronics and Communication Engineering: