logo

CuriousTab

CuriousTab

Discussion

Home ‣ Electronics and Communication Engineering ‣ Power Electronics Comments
  • Question

  • In a step down chopper using time ratio control, the input voltage is V and duty cycle is a. The load is purely resistive having resistance R. The average and rms load currents are


  • Options
  • A. In a step down chopper using time ratio control, the input voltage is V and duty cycle is a. The loa
  • B. In a step down chopper using time ratio control, the input voltage is V and duty cycle is a. The loa
  • C. In a step down chopper using time ratio control, the input voltage is V and duty cycle is a. The loa
  • D. In a step down chopper using time ratio control, the input voltage is V and duty cycle is a. The loa

  • Correct Answer
  •  

    • Power Electronics problems

    Search Results

    • 1. In brushless excitation system of modern alternators, the main exciter is

    • Options
    • A. dc generator
    • B. ac generator
    • C. either dc or ac generator
    • D. induction generator
      • Discuss
    • 2. An n pulse rectifier is fed by a source having an inductance L. If load current is I0, the voltage drop due to overlap is

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 3. In the circuit of figure, the waveshape of load current when thyristor conducting is

    • Options
    • A. constant
    • B. increasing exponentially
    • C. decreasing exponentially
    • D. either (b) or (c)
      • Discuss
    • 4. The symbol in figure is for

    • Options
    • A. SUS
    • B. SBS
    • C. SCS
    • D. None of the above
      • Discuss
    • 5. Assertion (A): A transistor has lower voltage drop during conduction as compared to thyristor

      Reason (R): Transistors are manufactured in very high voltage and current ratings.


    • Options
    • A. Both A and R are correct and R is correct explanation of A
    • B. Both A and R correct but R is not correct explanation of A
    • C. A is correct but R is wrong
    • D. A is wrong but R is correct
      • Discuss
    • 6. If 4 quadrant operation is required we need

    • Options
    • A. dual converter
    • B. full converter
    • C. semi converter
    • D. none of the above
      • Discuss
    • 7. A separately excited dc motor is run from a dc source through a chopper. At 600 rpm and rated torque, the duty cycle of chopper is 0.8. At 600 rpm and half the rated torque, the duty cycle is likely to be

    • Options
    • A. 0.9
    • B. 0.8
    • C. 0.75
    • D. 0.6
      • Discuss
    • 8. In a 3 phase full converter, the firing angle is less than 60°. The instantaneous output voltage

    • Options
    • A. will have positive part only
    • B. will have both positive and negative parts
    • C. may have both positive and negative parts
    • D. will have negative part if load is inductive
      • Discuss
    • 9. As compared to BJT, MOSFET has

    • Options
    • A. lower switching losses and higher conduction losses
    • B. higher switching losses and higher conduction losses
    • C. higher switching losses and lower conduction losses
    • D. lower switching losses and lower conduction losses
      • Discuss
    • 10. In pulse width modulation of chopper

    • Options
    • A. T is kept constant and Ton is varied
    • B. Ton is kept constant T is varied
    • C. both T and Ton are varied
    • D. either T or Ton is varied
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.