logo

CuriousTab

CuriousTab

Discussion

Home ‣ Civil Engineering ‣ GATE Exam Questions Comments
  • Question

  • If an ascending gradient of 1 in 50 meets another ascending gradient of 1 in 30 then the deviation angle is :


  • Options
  • A. If an ascending gradient of 1 in 50 meets another ascending gradient of 1 in 30 then the deviation a
  • B. If an ascending gradient of 1 in 50 meets another ascending gradient of 1 in 30 then the deviation a
  • C. If an ascending gradient of 1 in 50 meets another ascending gradient of 1 in 30 then the deviation a
  • D. If an ascending gradient of 1 in 50 meets another ascending gradient of 1 in 30 then the deviation a

  • Correct Answer
  •  

    • GATE Exam Questions problems

    Search Results

    • 1. The total thickness of pavement by CBR method depends on the CBR value of

    • Options
    • A. base course
    • B. surface course
    • C. subgrade
    • D. all layers
      • Discuss
    • 2. Mud pumping is commonly associated with

    • Options
    • A. bituminous penetration mecadam construction
    • B. cement concrete pavement on granular subgrade
    • C. premixed bituminous construction
    • D. cement concrete pavement on clay sub-grade
      • Discuss
    • 3. The strain energy stored in member AB of the pin-jointed truss shown in the below figure, when E and A are same for all members, is

    • Options
    • A. 2P2L/AE
    • B. P2L/AE
    • C. P2L/2AE
    • D. Zero
      • Discuss
    • 4. Cohesion in soil

    • Options
    • A. decreases active pressure and increases passive resistance
    • B. decreases both active pressure and passive resistance
    • C. increases the active pressure and decreases the passive resistance
    • D. increases both active pressure and passive resistance.
      • Discuss
    • 5. Permissible bending tensile stress in high yield strength deformed bars of grade 415 N/mm2 in a beam is :

    • Options
    • A. 190 N/mm2
    • B. 230 N/mm2
    • C. 140 N/mm2
    • D. None of the above
      • Discuss
    • 6. A continuous beam is loaded as shown in the figure below. Assuming a plastic moment capacity equal to MP, the minimum load at which the beam would collapse is

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 7. The consistency of a saturated cohesive soil is affected by

    • Options
    • A. water content
    • B. particle size distribution
    • C. density index
    • D. coefficient of permeability
      • Discuss
    • 8. Determine the correctness of otherwise of the following Assertion [A] and the Reason [R].

      Assertion [A] : The crown of the outgoing larger diameter sewer is always matched with the crown of incoming smaller diameter sewer.

      Reason [R] : It eliminates backing up of sewage in the incoming smaller diameter sewer.

    • Options
    • A. Both [A] and [R] are true and [R] is the correct reason for [A]
    • B. Both [A] and [R] are true and [R] is not the correct reason for [A]
    • C. Both [A] and [R] are false
    • D. [A] is true but [R] is false
      • Discuss
    • 9. Water distribution systems are sized to meet the

    • Options
    • A. maximum hourly demand
    • B. average hourly demand
    • C. maximum daily demand and fire demand
    • D. average daily demand and fire demand.
      • Discuss
    • 10. The settlement of prototype in granular material may be estimated using plate load test data from the following expression :

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.