logo

CuriousTab

CuriousTab

Discussion

Home ‣ Civil Engineering ‣ Structural Design Specifications Comments
  • Question

  • The greater clear dimension of web of thickness't' should not exceed


  • Options
  • A. 180 t
  • B. 200 t
  • C. 240 t
  • D. 270 t

  • Correct Answer
  • 270 t 

    • Structural Design Specifications problems

    Search Results

    • 1. The thickness of flat single lacing is, taken (where l is effective length of the bar).

    • Options
    • A.
    • B.
    • C.
    • D.
    • E.
      • Discuss
    • 2. The actual length of a column provided with a cap and base, is the distance between

    • Options
    • A. top of the base and underside of the cap
    • B. bottom of the base and underside of the cap
    • C. top of the base and top of the cap
    • D. bottom of the base and top of the cap.
      • Discuss
    • 3. The thickness of the rectangular plate for the cap or base of a solid round steel columns, is calculated from the formula where d is

    • Options
    • A. the reduced diameter of the column
    • B. the dimension of the base
    • C. the diameter of the base
    • D. the diameter of the top.
      • Discuss
    • 4. The anchorage value of standard U-type hook of a reinforcing bar of diameter d in tension, is

    • Options
    • A. 4 d
    • B. 8 d
    • C. 12 d
    • D. 16 d
    • E. 20 d
      • Discuss
    • 5. The spans of filler joists supporting a slab may be considered approximately equal if the longest span does not exceed the shortest span more than

    • Options
    • A. 5%
    • B. 10%
    • C. 15%
    • D. 20%
      • Discuss
    • 6. For under water concreting.

    • Options
    • A. at least 10 percent more cement is required as compared to dry conditions
    • B. the volume of coarse aggregates shall not be less than one and half times and not more than twice that of fine aggregate
    • C. the slump should not be less than 100 mm and not more than 180 mm
    • D. dewatering by pumping is not done or until 24 hours thereafter
    • E. All the above
      • Discuss
    • 7. Four reinforcing bars of 30 mm diameter each, are bundled in contact. The lower two bars extend up to end supports. The distance between the points of termination of the upper bars, is kept

    • Options
    • A. zero
    • B. 1.2 m
    • C. 0.9 m
    • D. 0.75 m
      • Discuss
    • 8. In the formula

    • Options
    • A. A and B are the dimensions of the column
    • B. A and B are the dimensions of the base plate
    • C. A is the greater projection of the plate beyond the column
    • D. B is the lesser projection of the plate beyond the column
    • E. Both (c) and (d) of above.
      • Discuss
    • 9. The staggered pitch is the distance between two consecutive rivets measured

    • Options
    • A. parallel to the direction of stress in the member
    • B. perpendicular to the direction of stress in the member
    • C. diagonally
    • D. none of these.
      • Discuss
    • 10. A column of rectangular section is considered short, if both the slenderness ratios are less than

    • Options
    • A. 8
    • B. 10
    • C. 12
    • D. 16
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.