logo

CuriousTab

CuriousTab

Discussion

Home ‣ Civil Engineering ‣ Structural Design Specifications Comments
  • Question

  • The anchorage value of standard U-type hook of a reinforcing bar of diameter d in tension, is


  • Options
  • A. 4 d
  • B. 8 d
  • C. 12 d
  • D. 16 d
  • E. 20 d

  • Correct Answer
  • 16 d 

    • Structural Design Specifications problems

    Search Results

    • 1. The spans of filler joists supporting a slab may be considered approximately equal if the longest span does not exceed the shortest span more than

    • Options
    • A. 5%
    • B. 10%
    • C. 15%
    • D. 20%
      • Discuss
    • 2. The slenderness effect of a wall is considered if the effective height of the wall exceeds the thickness

    • Options
    • A. 8 times
    • B. 10 times
    • C. 12 times
    • D. 16 times
      • Discuss
    • 3. Moist sand may contain surface water by mass upto

    • Options
    • A. 7.5%
    • B. 5.0%
    • C. 2.5%
    • D. 1.25%
      • Discuss
    • 4. The effective depth of a shallow beam is the distance between

    • Options
    • A. maximum compression and tension fibres
    • B. neutral axis and maximum compression fibre
    • C. neutral axis and maximum tension fibre
    • D. maximum compression fibre and the centroid of the tension reinforcement
    • E. none of these.
      • Discuss
    • 5. If the specified thickness of a footing is 100 cm, the depth of the form work may be tolerated from

    • Options
    • A. - 2 mm to + 2 mm
    • B. - 3 mm to + 3 mm
    • C. - 4 mm to + 4 mm
    • D. - 5 mm to + 5 mm
      • Discuss
    • 6. The thickness of the rectangular plate for the cap or base of a solid round steel columns, is calculated from the formula where d is

    • Options
    • A. the reduced diameter of the column
    • B. the dimension of the base
    • C. the diameter of the base
    • D. the diameter of the top.
      • Discuss
    • 7. The actual length of a column provided with a cap and base, is the distance between

    • Options
    • A. top of the base and underside of the cap
    • B. bottom of the base and underside of the cap
    • C. top of the base and top of the cap
    • D. bottom of the base and top of the cap.
      • Discuss
    • 8. The thickness of flat single lacing is, taken (where l is effective length of the bar).

    • Options
    • A.
    • B.
    • C.
    • D.
    • E.
      • Discuss
    • 9. The greater clear dimension of web of thickness't' should not exceed

    • Options
    • A. 180 t
    • B. 200 t
    • C. 240 t
    • D. 270 t
      • Discuss
    • 10. For under water concreting.

    • Options
    • A. at least 10 percent more cement is required as compared to dry conditions
    • B. the volume of coarse aggregates shall not be less than one and half times and not more than twice that of fine aggregate
    • C. the slump should not be less than 100 mm and not more than 180 mm
    • D. dewatering by pumping is not done or until 24 hours thereafter
    • E. All the above
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.