logo

CuriousTab

CuriousTab

Discussion

Home ‣ Civil Engineering ‣ Structural Design Specifications Comments
  • Question

  • For all practical purposes, the modulus of elasticity of steel is assumed


  • Options
  • A. 200 kN/mm2
  • B. 225 kN/mm2
  • C. 250 kN/mm2
  • D. 275 kN/mm2

  • Correct Answer
  • 200 kN/mm2 

    • Structural Design Specifications problems

    Search Results

    • 1. If the main reinforcement of the slab is parallel to a T-beam, the transverse reinforcement at mid span of the slab is provided at least ......of main reinforcement

    • Options
    • A. 40%
    • B. 50%
    • C. 60%
    • D. 70%.
      • Discuss
    • 2. To achieve uniform colour and consistency of the concrete by using ordinary Portland cement, the mixing time may be

    • Options
    • A. to 1 minute
    • B. 1 to minutes
    • C. to 2 minutes
    • D. 2 to minutes
    • E. none of these.
      • Discuss
    • 3. All reinforcement should be free from

    • Options
    • A. loose mill scales
    • B. loose rust
    • C. paints
    • D. oil
    • E. all the above.
      • Discuss
    • 4. If b is actual width of a flange, Dt is the thickness of the flange, b? is the breath of the web, lo is the distance between the points of zero moments in a beam, the effective width of the flange, is

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 5. Pick up the correct statement from the following:

    • Options
    • A. For steel castings, the minimum tensile strength is 41 kg/mm2 and minimum yield stress is 20.5 kg/mm2
    • B. For mild steel the minimum tensile strength is 44 kg/mm2 and minimum elongation of 23% on a gauge length of 5.65A
    • C. For high tensile steel, the minimum tensile strength is 58 kg/mm2
    • D. All the above.
      • Discuss
    • 6. For spans upto 10 m, the safe span to depth ratio for

    • Options
    • A. cantilever is 7
    • B. simply supported beams is 20
    • C. continuous beams is 26
    • D. all the above.
      • Discuss
    • 7. The angle of inclination of the lacing bars with axis of the member is kept between

    • Options
    • A. 20° and 50°
    • B. 30° and 60°
    • C. 40° and 70°
    • D. 50° and 80°
      • Discuss
    • 8. If fck is characteristic compressive strength of concrete, the flexural and split tensile strength fcr = afck N/mm2 where the value of a is

    • Options
    • A. 0.4
    • B. 0.5
    • C. 0.6
    • D. 0.7
    • E. 0.8
      • Discuss
    • 9. The minimum area of cross section of reinforcement in either direction of a slab should not be less than ...... of the slab cross section

    • Options
    • A. 0.75%
    • B. 0.10%
    • C. 0.15%
    • D. 0.20%
      • Discuss
    • 10. The thickness 't' of a rectangular column base which is provided for distributing the load uniformly, is calculated from the formula

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.