Discussion
Home ‣ Civil Engineering ‣ Steel Structure Design Comments
- Question
Cold driven rivets range from
Options- A. 6 to 10 mm in diameter
- B. 10 to 16 mm in diameter
- C. 12 to 22 mm in diameter
- D. 22 to 32 mm in diameter
- E. none of these.
- Correct Answer
- 12 to 22 mm in diameter
- 1. Effective length of a column effectively held in position at both ends and restrained in direction at one end, is
Options- A. L
- B. 0.67 L
- C. 0.85 L
- D. 1.5 L
- E. 2 L Discuss
- 2. In a built up section carrying a tensile force, the flanges of two channels are turned outward
Options- A. to simplify the transverse connections
- B. to minimise lacing
- C. to have greater lateral rigidity
- D. all the above
- E. none of the above. Discuss
- 3. The ratio of hydrostatic stress to the volumetric strain within the elastic range, is called
Options- A. modulus of elasticity
- B. shear modulus of elasticity
- C. bulk modulus of elasticity
- D. tangent modulus of elasticity
- E. all the above. Discuss
- 4. Outstanding length of a compression member consisting of a channel, is measured as
Options- A. half of the nominal width
- B. nominal width of the section
- C. from the edge to the first row of rivets
- D. none of these. Discuss
- 5. The channels get twisted symmetrically with regard to its axis
Options- A. parallel to flanges
- B. parallel to web
- C. perpendicular to flanges
- D. perpendicular to web. Discuss
- 6. The greatest gauge of long rivets should not exceed (where d is the diameter of the holes).
Options- A. 2 d
- B. 4 d
- C. 6 d
- D. 8 d
- E. 10 d Discuss
- 7. Design of a riveted joint, is based on the assumption:
Options- A. Load is uniformly distributed among all the rivets
- B. Shear stress on a rivet is uniformly distributed over its gross area
- C. Bearing stress is uniform between the contact surfaces of the plate and the rivet
- D. Bearing stress in the rivet is neglected
- E. All the above. Discuss
- 8. When the depth of a plate girder is at least n times the depth of vertical leg of the flange angles, the girder is known as deep plate girder, if n is
Options- A. 2
- B. 4
- C. 6
- D. 8
- E. 10 Discuss
- 9. Pick up the correct statement from the following:
Options- A. Tacking rivets are used if the minimum distance between centres of two adjacent rivets exceeds 12 t or 200 mm, whichever is less
- B. Tacking rivets are not considered to calculate stress
- C. Tacking rivets are provided throughout the length of a compression member composed of two components back to back
- D. All the above. Discuss
- 10. If the area of cross-section of a single angle discontinuous strut is 30 cm2 and allowable working stress corresponding to its slenderness ratio is 625 kg/cm2, the safe load carrying capacity of the member, is
Options- A. 10 tonnes
- B. 12 tonnes
- C. 15 tonnes
- D. 18 tonnes
- E. 20 tonnes Discuss
Steel Structure Design problems
Search Results
Correct Answer: 0.85 L
Correct Answer: to have greater lateral rigidity
Correct Answer: all the above.
Correct Answer: nominal width of the section
Correct Answer: parallel to web
Correct Answer: 8 d
Correct Answer: All the above.
Correct Answer: 8
Correct Answer: All the above.
Correct Answer: 15 tonnes
Comments
There are no comments.More in Civil Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.