Discussion
Home ‣ Civil Engineering ‣ Steel Structure Design Comments
- Question
Water pressure in a 80 cm water main is 10 kg/cm2. The minimum thickness of the metal required for the water main, not to be stressed more than 200 kg/cm2, is
Options- A. 1 cm
- B. 1.5 cm
- C. 2 cm
- D. 2.5 cm
- E. 3 cm
- Correct Answer
- 2 cm
- 1. Maximum permissible slenderness ratio of compression members which carry dead and superimposed load, is
Options- A. 350
- B. 250
- C. 180
- D. 80
- E. 75 Discuss
- 2. For the economical design of a combined footing to support two equal column loads, the projections of beams in lower tier are kept such that bending moment under column is equal to
Options- A. bending moment at the centre of the beam
- B. half the bending moment at the centre of the beam
- C. twice the bending moment at the centre of the beam
- D. none of these. Discuss
- 3. Working shear stress on the gross area of a rivet as recommended by Indian Standards, is
Options- A. 785 kg/cm2
- B. 1025 kg/cm2
- C. 2360 kg/cm2
- D. none of these. Discuss
- 4. According to I.S. : 800 - 1871, lacing bars resist transverse shear equal to
Options- A. 1.0% of the axial load
- B. 2.0% of the axial load
- C. 2.5% of the axial load
- D. 3.0% of the axial load
- E. 4.0% of the axial load. Discuss
- 5. The equivalent axial load may be defined as the load which produces a stress equal to
Options- A. maximum stress produced by the eccentric load
- B. maximum stressed fibre
- C. bending stress
- D. none of these. Discuss
- 6. The main type of butt joints, is a double cover
Options- A. shear riveted joint
- B. chain riveted joint
- C. zig-zag riveted joint
- D. all the above. Discuss
- 7. In a truss girder of a bridge, a diagonal consists of mild steel flat 4001.S.F. and carries a pull of 80 tonnes. If the grossdiameter of the rivet is 26 mm, the number of rivets required in the splice, is
Options- A. 6
- B. 7
- C. 8
- D. 9
- E. 12 Discuss
- 8. The channels get twisted symmetrically with regard to its axis
Options- A. parallel to flanges
- B. parallel to web
- C. perpendicular to flanges
- D. perpendicular to web. Discuss
- 9. Outstanding length of a compression member consisting of a channel, is measured as
Options- A. half of the nominal width
- B. nominal width of the section
- C. from the edge to the first row of rivets
- D. none of these. Discuss
- 10. The ratio of hydrostatic stress to the volumetric strain within the elastic range, is called
Options- A. modulus of elasticity
- B. shear modulus of elasticity
- C. bulk modulus of elasticity
- D. tangent modulus of elasticity
- E. all the above. Discuss
Steel Structure Design problems
Search Results
Correct Answer: 180
Correct Answer: bending moment at the centre of the beam
Correct Answer: 1025 kg/cm2
Correct Answer: 2.5% of the axial load
Correct Answer: maximum stress produced by the eccentric load
Correct Answer: all the above.
Correct Answer: 8
Correct Answer: parallel to web
Correct Answer: nominal width of the section
Correct Answer: all the above.
Comments
There are no comments.More in Civil Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.