logo

CuriousTab

CuriousTab

Discussion

Home ‣ Civil Engineering ‣ Steel Structure Design Comments
  • Question

  • Efficiency of a riveted joint is defined as the ratio of


  • Options
  • A. least strength of a riveted joint to the strength of solid plate
  • B. greatest strength of a riveted joint to the strength of solid plate
  • C. least strength of a riveted plate to the greatest strength of the riveted joint
  • D. all the above.

  • Correct Answer
  • all the above. 

    • Steel Structure Design problems

    Search Results

    • 1. If P is the wind pressure in kg/cm2, v is the velocity in km/hour and K is a constant of proportionality, then

    • Options
    • A. P = K/v2
    • B. v = K/P2
    • C. P = Kv2
    • D. P = Kv
      • Discuss
    • 2. Maximum permissible slenderness ratio of a member normally acting as a tie in a roof truss, is

    • Options
    • A. 180
    • B. 200
    • C. 250
    • D. 300
    • E. 350
      • Discuss
    • 3. The strength of ISA 125 = 75 x 10 mm used as a tie member with its longer leg connected at the ends by 27 mm diameter rivets, is

    • Options
    • A. 26,000 kg
    • B. 26,025 kg
    • C. 26,050 kg
    • D. 26,075 kg
    • E. 27,000 kg
      • Discuss
    • 4. The load on a lintel is assumed as uniformly distributed if the height of the masonry above it, is upto a height of

    • Options
    • A. the effective span
    • B. 1.25 times the effective span
    • C. 1.50 times the effective span
    • D. 2.0 times the effective span
    • E. 2.5 times the effective span.
      • Discuss
    • 5. If d is the distance between the flange angles of a plate girder, vertical stiffeners are provided at a distance not greater than

    • Options
    • A. d but not less than 0.20 d
    • B. 1.25 d but not less than 0.33 d
    • C. 1.5 d but not less than 0.33 d
    • D. 2.0 d but not less than 0.50 d
    • E. 2.5 d but not less than 0.50 d
      • Discuss
    • 6. If fbt and fc are the co-existent bending tensile stress and shear stress in a member, the equivalent stress fc is

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 7. For simply supported beams, the maximum permitted deflection, is

    • Options
    • A. 1/325 of the span
    • B. 1/350 of the span
    • C. 1/375 of the span
    • D. 1/400 of the span
    • E. none of these.
      • Discuss
    • 8. A structural member subjected to tensile force in a direction parallel to its logitudinal axis, is generally known as

    • Options
    • A. a tie
    • B. a tie member
    • C. a tension member
    • D. all the above.
      • Discuss
    • 9. The size of a butt weld is specified by the effective throat thickness which in the case of incomplete penetration, is taken as

    • Options
    • A. of the thickness of thicker part
    • B. of the thickness of thicker part
    • C. of the thickness of thinner part
    • D. of the thickness of thinner part
    • E. none of these.
      • Discuss
    • 10. The side thrust T on the tie rods provided at the end beam of jack arch of rise R, is calculated from the formula

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.