Discussion
Home ‣ Civil Engineering ‣ Steel Structure Design Comments
- Question
The permissible bearing stress in steel, is
Options- A. 1500 kg/cm2
- B. 1890 kg/cm2
- C. 2025 kg/cm2
- D. 2340 kg/cm2
- E. 2250 kg/cm2
- Correct Answer
- 1890 kg/cm2
- 1. The Indian standard code which deals with steel structures, is
Options- A. IS : 875
- B. IS : 800
- C. IS : 456
- D. IS : 1893 Discuss
- 2. The minimum pitch of rivet holes of diameter d should not be less than
Options- A. d
- B. 1.25 d
- C. 1.5 d
- D. 2 d
- E. 2.5 d Discuss
- 3. Rolled steel Tee-sections are used
Options- A. as columns
- B. with flat strips to connect plates in steel rectangular tanks
- C. as built up sections to resist axial tension
- D. none of these. Discuss
- 4. The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is
Options- A. 10 mm
- B. 15 mm
- C. 20 mm
- D. 25 mm
- E. 30 mm. Discuss
- 5. A pressure conduit carrying water beneath a stream or a canal, is known as
Options- A. sag
- B. depressed pipe
- C. inverted syphon
- D. all the above. Discuss
- 6. The gross diameter of a rivet is the diameter of
Options- A. cold rivet before driving
- B. rivet after driving
- C. rivet hole
- D. none of these. Discuss
- 7. The strength of a riveted lap joint is equal to its
Options- A. shearing strength
- B. bearing strength
- C. tearing strength
- D. least of (a), (b) and (c)
- E. greatest of (a) (b) and (c). Discuss
- 8. The main assumption of the method of simple design of steel frame work, is :
Options- A. beams are simply supported
- B. all connections of beams, girders and trusses are virtually flexible
- C. members in compression are subjected to forces applied at appropriate eccentricities
- D. all the above. Discuss
- 9. The equivalent axial load is obtained from the fomula
Options- A.
- B.
- C.
- D.
- E. none of these. Discuss
- 10. For a steel grillage footing to support two unequal column loads
Options- A. line of action of the resultant of two column loads, is made to coincide with the centre of gravity of the base of the footing
- B. trapezoidal shape is used for the base footing
- C. projections of beams on either side in lower tier are such that bending moments under columns are equal
- D. bending moment under the columns are kept equal to the bending moment between to two columns
- E. all the above. Discuss
Steel Structure Design problems
Search Results
Correct Answer: IS : 800
Correct Answer: 2.5 d
Correct Answer: with flat strips to connect plates in steel rectangular tanks
Correct Answer: 20 mm
Correct Answer: all the above.
Correct Answer: rivet after driving
Correct Answer: least of (a), (b) and (c)
Correct Answer: all the above.
Correct Answer:
Correct Answer: all the above.
Comments
More in Civil Engineering:
Programming
Copyright CuriousTab. All rights reserved.
Om du söker efter heta milfar som verkligen känner till vad de gor, da arplatsen for dig. Innehar hittar du 1 enorm samling utav nakna bilder pa sexiga kvinnor som alskar att uttrycka upp sina kroppar. Dessa milf-damer alskar att bli tagna fran alla hall och fa sprut over hela kroppshyddan. Det ar gratis, och gallerierna ar tillgangliga dygnet runtomkring – perfekt åkte dig som ska ha nagot till att njuta av varje dag.