CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Civil Engineering
‣
Strength of Materials
Comments
Question
If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by
Options
A. 2 times
B. 4 times
C. 8 times
D. 1/2 times
E. 3 times.
Correct Answer
8 times
Strength of Materials problems
Search Results
1. The bending moment is maximum on a section where shearing force
Options
A. is maximum
B. is minimum
C. is equal
D. changes sign.
Show Answer
Scratch Pad
Discuss
Correct Answer: changes sign.
2. Every material obeys the Hooke's law within its
Options
A. elastic limit
B. plastic point
C. limit of proportionality
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: limit of proportionality
3. As the elastic limit reaches, tensile strain
Options
A. increases more rapidly
B. decreases more rapidly
C. increases in proportion to the stress
D. decreases in proportion to the stress.
Show Answer
Scratch Pad
Discuss
Correct Answer: increases more rapidly
4. If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an axial pull of 3000 kg, the stress developed, is
Options
A. 9.5541 kg/cm
2
B. 95.541 kg/cm
2
C. 955.41 kg/cm
2
D. 9554.1 kg/cm
2
.
Show Answer
Scratch Pad
Discuss
Correct Answer: 955.41 kg/cm
2
5. The distance between the centres of adjacent rivets in the same row, is called
Options
A. pitch
B. lap
C. gauge
D. staggered pitch.
Show Answer
Scratch Pad
Discuss
Correct Answer: pitch
6. If the stress produced by a prismatic bar is equal to the working stress, the area of the cross-section of the prismatic bar, becomes
Options
A. zero
B. infinite
C. maximum
D. minimum.
Show Answer
Scratch Pad
Discuss
Correct Answer: infinite
7. The following assumption is not true in the theory of pure torsion :
Options
A. The twist along the shaft is uniform
B. The shaft is of uniform circular section throughout
C. Cross-section of the shaft, which is plane before twist remains plane after twist
D. All radii get twisted due to torsion.
Show Answer
Scratch Pad
Discuss
Correct Answer: All radii get twisted due to torsion.
8. Pick up the correct statement from the following :
Options
A. The rate of change of bending moment is equal to rate of shear force
B. The rate of change of shear force is equal to rate of loading
C. neither (a) nor (b)
D. both (a) and (b).
Show Answer
Scratch Pad
Discuss
Correct Answer: both (a) and (b).
9. If the beam is supported so that there are only three unknown reactive elements at the supports. These can be determined by using the following fundamental equation of statics
Options
A. ?
H
= 0
B. ?
V
= 0
C. ?
H
= 0; ?
H
= 0
D. ?
H
= 0; ?
V
= 0; ?
M
= 0
E. ?
M
= 0; ?
H
= 0
Show Answer
Scratch Pad
Discuss
Correct Answer: ?
H
= 0; ?
V
= 0; ?
M
= 0
10. In a continuous bending moment curve the point where it changes sign, is called
Options
A. point of inflexion
B. point of contraflexture
C. point of virtual hinge
D. all the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: all the above.
Comments
There are no comments.
Enter a new Comment
Save
More in Civil Engineering:
Advanced Surveying
Airport Engineering
Applied Mechanics
Building Construction
Building Materials
Concrete Technology
Construction Management
Docks and Harbours
Elements of Remote Sensing
Engineering Economy
Estimating and Costing
GATE Exam Questions
Highway Engineering
Hydraulics
Irrigation
Railways
RCC Structures Design
SI Units
Soil Mechanics and Foundation Engineering
Steel Structure Design
Strength of Materials
Structural Design Specifications
Surveying
Theory of Structures
Tunnelling
UPSC Civil Service Exam Questions
Waste Water Engineering
Water Resources Engineering
Water Supply Engineering