logo

CuriousTab

CuriousTab

Discussion


Home Civil Engineering Strength of Materials Comments

  • Question
  • A cantilever carries is uniformly distributed load W over its whole length and a force W acts at its free end upward. The net deflection of the free end will be


  • Options
  • A. zero
  • B. A cantilever carries is uniformly distributed load W over its whole length and a force W acts at its upward
  • C. A cantilever carries is uniformly distributed load W over its whole length and a force W acts at its downward
  • D. none of these.

  • Correct Answer
  • upward 


  • Strength of Materials problems


    Search Results


    • 1. A member which is subjected to reversible tensile or compressive stress may fail at a stress lower than the ultimate stress of the material. This property of metal, is called

    • Options
    • A. plasticity of the metal
    • B. elasticity of the metal
    • C. fatigue of the metal
    • D. workability of the metal.
    • Discuss
    • 2. In a square beam loaded longitudinally, shear develops

    • Options
    • A. on middle fibre along horizontal plane
    • B. on lower fibre along horizontal plane
    • C. on top fibre along vertical plane
    • D. equally on each fibre along horizontal plane
    • E. none of these.
    • Discuss
    • 3. If a solid shaft is subjected to a torque T at its end such that maximum shear stress does not exceed fz the diameter of the shaft will be

    • Options
    • A.
    • B.
    • C.
    • D. none of these.
    • Discuss
    • 4. In the given below figure, the rivets with maximum stress, are :

    • Options
    • A. 1 and 2
    • B. 1 and 3
    • C. 3 and 4
    • D. 2 and 4
    • Discuss
    • 5. Euler's formula states that the buckling load P for a column of length l, both ends hinged and whose least moment of inertia and modulus of elasticity of the material of the column are I and E respectively, is given by the relation

    • Options
    • A.
    • B.
    • C.
    • D.
    • E. P = ?El2.
    • Discuss
    • 6. Pick up the correct statement from the following :

    • Options
    • A. The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance
    • B. In visco-elastic material, stress-strain relation is dependent on time
    • C. An instropic material has different properties is different directions
    • D. An orthotropic material has different properties in three mutually perpendicular directions
    • E. All the above.
    • Discuss
    • 7. In a simply supported beam (l + 2a) with equal overhangs (a) and carrying a uniformly distributed load over its entire length, B.M. at the middle point of the beam will be zero if

    • Options
    • A. l = 2a
    • B. l = 4a
    • C. l < 2a
    • D. l > a
    • E. l > 3a.
    • Discuss
    • 8. The principal stresses at a point are 100, 100 and-200 kgf/cm2, the octo hedral shear stress at the point is :

    • Options
    • A. 100 2 kg/cm2
    • B. 200 2 kg/cm2
    • C. 300 2 kg/cm2
    • D. 400 2 kg/cm2
    • E. 500 2 kg/cm2.
    • Discuss
    • 9. If a member is subjected to a tensile force P, having its normal cross-section A, the resulting shear stress in an oblique plane inclined at an angle ? to its transverse plane, is

    • Options
    • A.
    • B.
    • C.
    • D.
    • E.
    • Discuss
    • 10. In a simply supported beam L with a triangular load W varying from zero at one end to the maximum value at the other end, the maximum bending moment is

    • Options
    • A.
    • B.
    • C.
    • D.
    • E.
    • Discuss


    Comments

    There are no comments.

Enter a new Comment