logo

CuriousTab

CuriousTab

Discussion

Home ‣ Civil Engineering ‣ Theory of Structures Comments
  • Question

  • Pick up the correct statement from the following:


  • Options
  • A. The bending stress in a section is zero at its neutral axis and maximum at the outer fibres
  • B. The shear stress is zero at the outer fibres and maximum at the neutral axis
  • C. The bending stress at the outer fibres, is known as principal stress
  • D. The planes of principal stresses are inclined at 45° to the neutral plane
  • E. All the above.

  • Correct Answer
  • All the above. 

    • Theory of Structures problems

    Search Results

    • 1. The moment of inertia of a triangular section (height h, base b) about its base, is

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 2. A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 x 106 N/mm2, the deflection of the free end, is

    • Options
    • A. 2 mm
    • B. 3 mm
    • C. 4 mm
    • D. 5 mm
    • E. 6 mm
      • Discuss
    • 3. In the truss, the force in the member AC is

    • Options
    • A. 6.25 t compressive
    • B. 8.75 t tentile
    • C. t tensile
    • D. t compressive.
      • Discuss
    • 4. A three hinged arch is generally hinged at its supports and

    • Options
    • A. at one quarter span
    • B. at the crown
    • C. any where in the rib
    • D. none of these.
      • Discuss
    • 5. The ratio of the length and diameter of a simply supported uniform circular beam which experiences maximum bending stress equal to tensile stress due to same load at its mid span, is

    • Options
    • A.
    • B.
    • C.
    • D.
    • E. 1.0
      • Discuss
    • 6. If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 x 105 N/mm2) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2, the angle of twist in radians, is

    • Options
    • A. 0.001
    • B. 0.002
    • C. 0.0025
    • D. 0.003
    • E. 0.005
      • Discuss
    • 7. The general expression for the B.M. of a beam of length l is the beam carries

    • Options
    • A. a uniformly distributed load w/unit length
    • B. a load varying linearly from zero at one end to w at the other end
    • C. an isolated load at mid span
    • D. none of these.
      • Discuss
    • 8. A cantilever of length L is subjected to a bending moment M at its free end. If EI is the flexural rigidity of the section, the deflection of the free end, is

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 9. The horizontal thrust on the ends of a two hinged semicircular arch of radius R carrying

    • Options
    • A. a uniformly distributed load ? per unit run over its right half span, is
    • B. a uniformly distributed load ? per unit run over its entire span is
    • C. a distributed load varying from zero at the left end to ? per unit horizontal run at the right end, is
    • D. all the above.
      • Discuss
    • 10. The normal and tangential components of stress on an inclined plane through ?° to the direction of the force, will be equal if ? is

    • Options
    • A. 45°
    • B. 30°
    • C. 60°
    • D. 90°
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.