logo

CuriousTab

CuriousTab

Discussion


Home Civil Engineering Railways See What Others Are Saying!
  • Question
  • The main function of sleepers, is


  • Options
  • A. to support rails
  • B. to hold rails at correct gauge
  • C. to distribute load from the rails to ballast
  • D. all the above.

  • Correct Answer
  • all the above. 


  • More questions

    • 1. A three hinged arch is loaded with an isolated load 1000 kg at a horizontal distance of 2.5 m from the crown, 1 m above the level of hinges at the supports 10 metres apart. The horizontal thrust is

    • Options
    • A. 1250 kg
    • B. 125 kg
    • C. 750 kg
    • D. 2500 kg
    • E. 2325 kg.
    • Discuss
    • 2. A short column 20 cm x 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2, the Safe load on the column, should not exceed

    • Options
    • A. 4120 kg
    • B. 41, 200 kg
    • C. 412, 000 kg
    • D. none of these.
    • Discuss
    • 3. In setting up a plane table at any station

    • Options
    • A. levelling is done first
    • B. centering is done first
    • C. both levelling and centering are done simultaneously
    • D. orientation is done first.
    • Discuss
    • 4. A prestressed rectangular beam which carries two concentrated loads W at L/3 from either end, is provided with a bent tendon with tension P such that central one-third portion of the tendon remains parallel to the longitudinal axis, the maximum dip h is

    • Options
    • A.
    • B.
    • C.
    • D.
    • E.
    • Discuss
    • 5. The velocity of a body fallen from height h, on reaching the ground is given by

    • Options
    • A. v = 2gh
    • B. v = 2gh2
    • C. v = 2gh
    • D. v = 1/2gh
    • E. h2/2g
    • Discuss
    • 6. Symon's rain gauge is

    • Options
    • A. tipping-bucket gauge
    • B. weighing type gauge
    • C. float recording gauge
    • D. non-recording gauge.
    • Discuss
    • 7. The various stages occuring in GPS system are described below :
      1. Generation of an output to the user
      2. Detection of the GPS signal
      3. Processing the data in the built-in-computer
      4. Decoding the GPS signal.
      The correct sequence of the stages is :

    • Options
    • A. 1, 2, 3, 4
    • B. 2, 3, 4, 1
    • C. 2, 4, 3, 1
    • D. 3, 1, 2 , 4
    • Discuss
    • 8. Pick up the correct statement from the following:

    • Options
    • A. The speed of the aircraft relative to the ground, is called cruising speed
    • B. The speed of the aircraft relative to wind, is called air speed
    • C. When wind is blowing the direction of the flight, air speed is less than cruising speed
    • D. All the above.
    • Discuss
    • 9. With a clinging nappe of a weir, the excess discharge, is

    • Options
    • A. 6% to 7%
    • B. 8% to 10%
    • C. 18% to 20%
    • D. 25% to 30%
    • E. 30% to 40%.
    • Discuss
    • 10. Pick up the correct statement from the following:

    • Options
    • A. Air screw converts the energy given by the engine into speed
    • B. The propellers which are driven by turbine engines, are technically called turboprops
    • C. The aircrafts which obtain the thrust directly from turbine engine, are called turbo-jets
    • D. The aircraft which is filled with a fan infront of turbo-jet engine, is called turbofan propelled aeroplane
    • E. All the above.
    • Discuss


    Comments

    There are no comments.

Enter a new Comment